zorruno-homeassistant/esphome/esp-downstairskitchleds.yaml

##########################################################################################
##########################################################################################
# Title:    DOWNSTAIRS KITCHEN - OVER PANTRY LEDS
# Hardware: Sinilink Mosfet Board XY-VFMS (ESP8266) 
#           https://devices.esphome.io/devices/Sinilink-XY-VFMS
# Repo:     https://home.fox.co.nz/gitea/zorruno/zorruno-homeassistant/src/branch/master/esphome/esp-downstairskitchleds.yaml
#
# V1.1 - 2025-08-18 Full tidyup as general purpose LED strip controller
# V1.0 - 2025-08-17 First Setup (and replacement of Tasmota)
#
# ------------------------------------------
# DEVICE GPIO Sinilink XY-VFMS
# ------------------------------------------
# GPIO02	Blue LED (We'll use this for ESPHome status)
# GPIO04	Mosfet Output (0V when switched) and Red LED
# GPIO12	Toggle Button
# GPIO13	Green LED (We'll use this to display fading status)
#
# ------------------------------------------
# OPERATION (as at V1.1)
# ------------------------------------------
# 1. General Purpose LED controller
# 2. Designed for a Sinilink XY-VFMS board that has a mosfet output and supposedly will handle
#    5A and a DC input of 5V-36V.
# 3. Has global setting for MAX % PWM output for the LEDs so you can give them a longer life.
# 4. Has a min setting for the LEDs and it will switch off if it goes below that to stop any
#    flicker at very low PWM outputs.
# 5. PWM freq is set to 2kHz, but you could potentially ramp it up.  I was getting resets at
#    higher values with this device, but other devices may be better.  Obviously if yoou use
#    an esp32 you can set it much higher (40kHz I think is the max?)
# 6. Min and Max output settings aren't set in Home assistant/MQTT, but you could do this if
#    needed.  With a 1MB flash, it is starting to get tight.  I have done minimal optimising
#    at this stage though.
# 7. There are PACKAGES included for the common things such as the network
#    items, diagnostic entities, MQTT and SNTP (if needed, get them from the repo or use your own)
# 8. Default config is to always fade slowly up to full when powered up (so can be deployed with
#    no network etc)
# 9. The green LED on the sinilink flashes whilst fading (differently for up/down).  The red LED
#    follows the output (it is the same GPIO as the MOSFET)  
# 10.Timing of fades should be based on settings, or a percentage of them if eg already half brightness.
# 11.A useful 3D printed case: https://cults3d.com/en/3d-model/tool/snapfit-enclosure-for-esp8266-sinilink-xy-wfms-5v-36v-mosfet-switch-module
# 12.Some things you can change in Home Assistant/MQTT
#    - Start up function
#    - Up/Down/Stop fade buttons
#    - A fade up/fade down switch
#    - Normal on/off switch (quick ramp up/down)
#    - Setting for fade up and fade times (0-60 seconds)
#    - Output display of % PWM output
#    - Ability to set output to any value (1-100, but respects min/max)
#    - Default has a bunch of device diagnostic in the PACKAGE included (Sensors_Common)
#
###########################################################################################
##########################################################################################

##########################################################################################
# SPECIFIC DEVICE VARIABLE SUBSTITUTIONS
# If NOT using a secrets file, just replace these with the passwords etc (in quotes)
##########################################################################################
substitutions:
  # Device Naming
  device_name: "esp-downstairskitchleds"
  friendly_name: "Downstairs Kitchen LEDs"
  description_comment: "Downstairs Kitchen Over Pantry LEDs :: Sinilink XY-WFMS"
  device_area: "Downstairs Kitchen" # Allows ESP device to be automatically linked to an 'Area' in Home Assistant. 

  # Project Naming
  project_name: "Sinilink.XY-WFMS" # Project Details 
  project_version: "v1.1"  # Project V denotes release of yaml file, allowing checking of deployed vs latest version
  
  # Passwords & Secrets
  api_key: !secret esp-api_key
  ota_pass: !secret esp-ota_pass 
  static_ip_address: !secret esp-downstairskitchleds_ip # unfortunately you can't use substitutions inside secrets names
  mqtt_local_command_main_topic: !secret mqtt_local_command_main_topic
  mqtt_local_status_main_topic: !secret mqtt_local_status_main_topic
  
  # Device Settings
  log_level: "INFO" # Define logging level: NONE, ERROR, WARN, INFO, DEBUG (Default), VERBOSE, VERY_VERBOSE
  update_interval: "20s" # update time for for general sensors etc

  # MQTT LOCAL Controls
  mqtt_local_device_name: "downstairskitchen-pantryleds"
  mqtt_local_command_topic: "${mqtt_local_command_main_topic}/${mqtt_local_device_name}" # Topic we will use to command this locally without HA
  mqtt_local_status_topic: "${mqtt_local_status_main_topic}/${mqtt_local_device_name}" # Topic we will use to view status locally without HA
  mqtt_local_device_command_ON: "ON"
  mqtt_local_device_command_OFF: "OFF"

  # MQTT REMOTE Controls
  #mqtt_remote_device_name: "downstairskitchen-pantryleds"
  #mqtt_remote_device_command_topic: "${mqtt_local_command_main_topic}/${mqtt_remote_device_name}/light/set"
  #mqtt_remote_device_command1: "+"
  #mqtt_remote_device_command2: "-"
  #mqtt_remote_device_command3: "0"
  #mqtt_local_status_topic: "${mqtt_local_status_main_topic}/${mqtt_remote_device_name}/speed/state" # Topic we will use to view status locally without HA

  # Button Naming & Icons

  # Switch/Relay Naming & Icons

##########################################################################################
# PACKAGES: Included Common Packages
# https://esphome.io/components/packages.html
##########################################################################################
packages:
  common_wifi: !include
    file: common/network_common.yaml
    vars:
      local_device_name: "${device_name}"
      local_static_ip_address: "${static_ip_address}"
      local_ota_pass: "${ota_pass}"
  common_api: !include
    file: common/api_common.yaml
    vars:
      local_api_key: "${api_key}"
  #common_webportal: !include
  #  file: common/webportal_common.yaml
  common_mqtt: !include
    file: common/mqtt_common.yaml
    vars:
      local_device_name: "${device_name}"
  #common_sntp: !include
  #  file: common/sntp_common.yaml
  common_general_sensors: !include
    file: common/sensors_common.yaml
    vars:
      local_friendly_name: "${friendly_name}"
      local_update_interval: "${update_interval}"

##########################################################################################
# ESPHome CORE CONFIGURATION
# https://esphome.io/components/esphome.html
##########################################################################################
esphome:
  name: "${device_name}"
  friendly_name: "${friendly_name}"
  comment: "${description_comment}" # Appears on the esphome page in HA
  area: "${device_area}"
  on_boot:
    priority: -200
    then:
      - lambda: |-
          ESP_LOGI("boot", "Last reset reason: %s", ESP.getResetReason().c_str());
          // Keep the HA dropdown in sync with the stored mode
          switch (id(restart_mode)) {
            case 0: id(restart_action).publish_state("Fade up to full"); break;
            case 1: id(restart_action).publish_state("Restore Brightness"); break;
            case 2: default: id(restart_action).publish_state("Remain Off"); break;
          }
      # Mode 0: Fade up to full (respect min/max & ramp time)
      - if:
          condition:
            lambda: 'return id(restart_mode) == 0;'
          then:
            - lambda: 'id(ramp_switch_target_on) = true;'
            - script.execute: ramp_on_script
      # Mode 1: Restore Brightness quickly
      - if:
          condition:
            lambda: 'return id(restart_mode) == 1;'
          then:
            - lambda: |-
                // Clamp the remembered brightness to valid bounds
                float target = id(last_brightness_pct);
                if (target < 0.0f)  target = 0.0f;
                if (target > 100.0f) target = 100.0f;
                float minp = (float) id(min_brightness_pct);
                float maxp = (float) id(max_brightness_pct);
                if (target > 0.0f) {
                  if (target < minp) target = minp;
                  if (target > maxp) target = maxp;
                }
                id(suppress_slider_sync) = true;
                if (target <= 0.0f) {
                  auto call = id(mosfet_leds).make_call();
                  call.set_state(false);
                  call.set_transition_length(0);
                  call.perform();
                  id(ramp_switch_target_on) = false;
                } else {
                  auto call = id(mosfet_leds).make_call();
                  call.set_state(true);
                  call.set_brightness(target / 100.0f);
                  call.set_transition_length(150);
                  call.perform();
                  id(ramp_switch_target_on) = true;
                }
            - delay: 300ms
            - lambda: 'id(suppress_slider_sync) = false;'
      # Mode 2: Remain Off
      - if:
          condition:
            lambda: 'return id(restart_mode) == 2;'
          then:
            - script.stop: ramp_on_script
            - script.stop: ramp_off_script
            - light.turn_off:
                id: mosfet_leds
                transition_length: 0s
            - lambda: 'id(ramp_switch_target_on) = false;'

##########################################################################################
# ESP PLATFORM AND FRAMEWORK
# https://esphome.io/components/esp8266.html
# https://esphome.io/components/esp32.html
##########################################################################################
esp8266:
  board: esp01_1m
  restore_from_flash: true # restore some values on reboot

preferences:
  flash_write_interval: 5min

mdns:
  disabled: false # Disabling will make the build file smaller (and it is still available via static IP)

##########################################################################################
# GLOBAL VARIABLES
# https://esphome.io/components/globals.html
##########################################################################################
globals:
  # Minimum Brightness % for LEDs (will switch off if <=)
  - id: min_brightness_pct
    type: int
    restore_value: true
    initial_value: '3'        # start/finish at X%
  # Maximum Brightness % for LEDs (should never go beyond this)
  - id: max_brightness_pct
    type: int
    restore_value: false
    initial_value: '90'       # hard cap; never exceed this
  # Default Fading Up Time (Selectable and will be retained)
  - id: ramp_up_ms            # fade-in when turned ON
    type: int
    restore_value: true
    initial_value: '5000'     # 5 s
  # Default Fading Down Time (Selectable and will be retained)
  - id: ramp_down_ms          # fade-out when turned OFF
    type: int
    restore_value: true
    initial_value: '10000'    # 10 s
  # Action on Restart. (0=Fade full, 1=Restore brightness, 2=Remain off)
  - id: restart_mode                  
    type: int
    restore_value: true
    initial_value: '0'        # default = Fade Up to Full (so can be deployed with no other setup)
  
  # Determine last fade direction.
  # true when you asked the light to end up ON (Ramp Up)
  # false when you asked the light to end up OFF (Ramp Down)
  - id: ramp_switch_target_on
    type: bool
    restore_value: true
    initial_value: 'false'
  # Prevent jitter when adjusting the slider
  - id: suppress_slider_sync
    type: bool
    restore_value: false
    initial_value: 'false'
  # actual 0..100 seen last time, for restart  
  - id: last_brightness_pct          
    type: float
    restore_value: true
    initial_value: '0.0'
  # last published "Output Set (0-100)" integer
  - id: last_set_pos
    type: int
    restore_value: false
    initial_value: '-1'
  # helper to keep blink time == transition time  
  - id: last_ramp_ms
    type: int
    restore_value: false
    initial_value: '0'        

##########################################################################################    
# LOGGER COMPONENT
# https://esphome.io/components/logger.html
# Logs all log messages through the serial port and through MQTT topics.
########################################################################################## 
logger:
  level: "${log_level}"  # INFO Level suggested, or DEBUG for testing
  baud_rate: 0 # set to 0 for no logging via UART, needed if you are using it for other serial things (eg PZEM, Serial control)

##########################################################################################
# MQTT COMMANDS
# This adds device-specific MQTT command triggers to the common MQTT configuration.
##########################################################################################
mqtt:
  on_message:
    # Light control to ramp up
    - topic: "${mqtt_local_command_topic}/light/set"
      payload: "${mqtt_local_device_command_ON}"
      then:
        - switch.turn_on: mosfet_ramp_switch
    # Light control to ramp up
    - topic: "${mqtt_local_command_topic}/light/set"
      payload: "${mqtt_local_device_command_OFF}"
      then:
        - switch.turn_off: mosfet_ramp_switch

#########################################################################################
# STATUS LED
# https://esphome.io/components/status_led.html
#########################################################################################
# SINILINK: Status LED Blue LED on GPIO2, active-low
#########################################################################################
status_led:
  pin:
    number: GPIO2
    inverted: true

##########################################################################################
# SWITCH COMPONENT
# https://esphome.io/components/switch/
##########################################################################################
switch:
  # Ramp-aware ON/OFF for HA (asymmetric, eased; no bounce)
  - platform: template
    id: mosfet_ramp_switch
    name: "${friendly_name} Fade Up/Down"
    icon: mdi:led-strip-variant
    lambda: |-
      return id(ramp_switch_target_on);
    turn_on_action:
      - lambda: 'id(ramp_switch_target_on) = true;'
      - script.stop: ramp_off_script
      - script.execute: ramp_on_script
    turn_off_action:
      - lambda: 'id(ramp_switch_target_on) = false;'
      - script.stop: ramp_on_script
      - script.execute: ramp_off_script

#################################################################################################
# BUTTON COMPONENT
# https://esphome.io/components/button/index.html
#################################################################################################
button:
  # Start ramping UP (from current level)
  - platform: template
    id: fade_up_button
    name: "${friendly_name} Fade Up"
    icon: mdi:arrow-up-bold
    on_press:
      - lambda: |-
          id(ramp_switch_target_on) = true;
          id(mosfet_ramp_switch).publish_state(true);   // reflect in HA immediately
      - script.stop: ramp_off_script
      - script.execute: ramp_on_script

  # Start ramping DOWN (from current level)
  - platform: template
    id: fade_down_button
    name: "${friendly_name} Fade Down"
    icon: mdi:arrow-down-bold
    on_press:
      - lambda: |-
          id(ramp_switch_target_on) = false;
          id(mosfet_ramp_switch).publish_state(false);  // reflect in HA immediately
      - script.stop: ramp_on_script
      - script.execute: ramp_off_script

  # STOP any ramping (hold current brightness)
  - platform: template
    id: fade_stop_button
    name: "${friendly_name} Fade Stop"
    icon: mdi:pause
    on_press:
      # Stop any pending scripts (and their delayed turn_off)
      - script.stop: ramp_on_script
      - script.stop: ramp_off_script
      - script.stop: led_flash_up
      - script.stop: led_flash_down
      - output.turn_off: green_led_out
      # Cancel the light's transition by commanding the current level with 0 ms,
      # but DO NOT change the ramp switch state/flag.
      - lambda: |-
          const auto &cv = id(mosfet_leds).current_values;
          if (cv.is_on()) {
            auto call = id(mosfet_leds).make_call();
            call.set_state(true);
            call.set_brightness(cv.get_brightness());
            call.set_transition_length(0);
            call.perform();
          }

#########################################################################################
# SELECT COMPONENT
# https://esphome.io/components/select/index.html
#########################################################################################
select:
  - platform: template
    id: restart_action
    name: "${friendly_name} Restart Action"
    icon: mdi:restart
    optimistic: true
    options:
      - "Fade up to full"
      - "Restore Brightness"
      - "Remain Off"
    initial_option: "Restore Brightness"
    set_action:
      - lambda: |-
          if (x == "Fade up to full") {
            id(restart_mode) = 0;
          } else if (x == "Restore Brightness") {
            id(restart_mode) = 1;
          } else {
            id(restart_mode) = 2;
          }

#########################################################################################
# BINARY SENSORS
# https://esphome.io/components/binary_sensor/
#########################################################################################
binary_sensor:
  - platform: gpio
    id: btn_gpio12
    name: "${friendly_name} Button"
    pin:
      number: GPIO12
      mode:
        input: true
        pullup: true
      inverted: true
    filters:
      - delayed_on: 20ms
      - delayed_off: 20ms
    on_press:
      - if:
          condition:
            lambda: 'return id(ramp_switch_target_on);'
          then:
            # Target is currently ON → press should go OFF (start ramp-down)
            - lambda: |-
                id(ramp_switch_target_on) = false;
                id(mosfet_ramp_switch).publish_state(false);  // reflect in HA immediately
            - script.stop: ramp_on_script
            - script.execute: ramp_off_script
          else:
            # Target is currently OFF → press should go ON (start ramp-up)
            - lambda: |-
                id(ramp_switch_target_on) = true;
                id(mosfet_ramp_switch).publish_state(true);   // reflect in HA immediately
            - script.stop: ramp_off_script
            - script.execute: ramp_on_script

##########################################################################################
# SENSOR COMPONENT
# https://esphome.io/components/sensor/
##########################################################################################
sensor:
  - platform: template
    id: mosfet_output_pct
    name: "${friendly_name} Output (%)"
    unit_of_measurement: "%"
    icon: mdi:percent
    accuracy_decimals: 0
    update_interval: 100ms   # consider 200ms if you want fewer updates
    lambda: |-
      const auto &cv = id(mosfet_leds).current_values;
      return cv.is_on() ? (cv.get_brightness() * 100.0f) : 0.0f;
    on_value:
      then:
        - lambda: |-
            // Remember latest actual output (0..100) for "Restore Brightness"
            id(last_brightness_pct) = x;

            // If not suppressing sync, update the 0..100 slider only when its INT changes
            if (!id(suppress_slider_sync)) {
              float actual = x;                                // actual %
              float minp = (float) id(min_brightness_pct);
              float maxp = (float) id(max_brightness_pct);
              if (maxp <= minp) maxp = minp + 1.0f;
              float pos = (actual <= 0.0f) ? 0.0f : ((actual - minp) * 100.0f / (maxp - minp));
              if (pos < 0.0f) pos = 0.0f;
              if (pos > 100.0f) pos = 100.0f;
              int pos_i = (int) floorf(pos + 0.5f);

              if (pos_i != id(last_set_pos)) {
                id(last_set_pos) = pos_i;
                id(led_output_set_pct).publish_state(pos_i);
              }
            }

##########################################################################################
# OUTPUT COMPONENT
# https://esphome.io/components/light/index.html
##########################################################################################
# An OUTPUT can be binary (0,1) or float, which is any value between 0 and 1.
# PWM Outputs such as "ledc" are float. https://esphome.io/components/output/ledc.html
##########################################################################################
output:
  - platform: esp8266_pwm
    id: mosfet_pwm
    pin: GPIO4
    frequency: 2000 Hz   # high frequency to avoid audible/visible artifacts
  - platform: gpio
    id: green_led_out    # Green LED
    pin:
      number: GPIO13
      inverted: false

##########################################################################################
# LIGHT COMPONENT
# https://esphome.io/components/light/
##########################################################################################
light:
  - platform: monochromatic
    id: mosfet_leds
    name: "${friendly_name}"
    output: mosfet_pwm
    restore_mode: RESTORE_DEFAULT_OFF
    default_transition_length: 2s
    icon: mdi:led-strip-variant
    gamma_correct: 1.2
    on_turn_on:
      - mqtt.publish:
          topic: "${mqtt_local_status_topic}/light/state"
          payload: "${mqtt_local_device_command_ON}"
          retain: true
      - lambda: 'id(ramp_switch_target_on) = true;'
    on_turn_off:
      - mqtt.publish:
          topic: "${mqtt_local_status_topic}/light/state"
          payload: "${mqtt_local_device_command_OFF}"
          retain: true
      - lambda: 'id(ramp_switch_target_on) = false;'
    on_state:
      - lambda: |-
          const float cap = id(max_brightness_pct) / 100.0f;
          const auto &cv = id(mosfet_leds).current_values;
          if (cv.is_on() && cv.get_brightness() > cap + 0.001f) {
            auto call = id(mosfet_leds).make_call();
            call.set_state(true);
            call.set_brightness(cap);
            call.set_transition_length(0);
            call.perform();
          }

##########################################################################################
# NUMBER COMPONENT
# https://esphome.io/components/number/
##########################################################################################
number:
  - platform: template
    id: cfg_ramp_up_s
    name: "${friendly_name} Fade Up Time (s)"
    entity_category: config
    unit_of_measurement: s
    icon: mdi:timer-sand
    mode: slider
    min_value: 0
    max_value: 60
    step: 1
    lambda: |-
      return (float) id(ramp_up_ms) / 1000.0f;
    set_action:
      - lambda: |-
          int secs = (int) floorf(x + 0.5f);
          if (secs < 0) secs = 0;
          if (secs > 60) secs = 60;
          id(ramp_up_ms) = secs * 1000;
          id(cfg_ramp_up_s).publish_state((float) secs);

  - platform: template
    id: cfg_ramp_down_s
    name: "${friendly_name} Fade Down Time (s)"
    entity_category: config
    unit_of_measurement: s
    icon: mdi:timer-sand-complete
    mode: slider
    min_value: 0
    max_value: 60
    step: 1
    lambda: |-
      return (float) id(ramp_down_ms) / 1000.0f;
    set_action:
      - lambda: |-
          int secs = (int) floorf(x + 0.5f);
          if (secs < 0) secs = 0;
          if (secs > 60) secs = 60;
          id(ramp_down_ms) = secs * 1000;
          id(cfg_ramp_down_s).publish_state((float) secs);

  - platform: template
    id: led_output_set_pct
    name: "${friendly_name} Output Set (0-100)"
    icon: mdi:tune
    mode: slider
    min_value: 0
    max_value: 100
    step: 1
    # Show current position mapped into 0..100 across [min..max]
    lambda: |-
      const auto &cv = id(mosfet_leds).current_values;
      float actual = cv.is_on() ? (cv.get_brightness() * 100.0f) : 0.0f;  // 0..100 actual
      float minp = (float) id(min_brightness_pct);
      float maxp = (float) id(max_brightness_pct);
      if (maxp <= minp) maxp = minp + 1.0f;  // avoid div/0
      if (actual <= 0.0f) return 0.0f;       // when OFF, show 0
      float pos = (actual - minp) * 100.0f / (maxp - minp);
      if (pos < 0.0f) pos = 0.0f;
      if (pos > 100.0f) pos = 100.0f;
      return floorf(pos + 0.5f);             // integer
    set_action:
      - if:
          condition:
            lambda: 'return x <= 0.0f;'
          then:
            # 0 means OFF
            - lambda: 'id(suppress_slider_sync) = true;'
            - script.stop: ramp_on_script
            - script.stop: ramp_off_script
            - light.turn_off:
                id: mosfet_leds
                transition_length: 200ms
            - lambda: |-
                id(ramp_switch_target_on) = false;
                id(led_output_set_pct).publish_state(0);
            - delay: 400ms
            - lambda: 'id(suppress_slider_sync) = false;'
          else:
            # Map 1..100 → [min..max] and set ON
            - lambda: |-
                id(suppress_slider_sync) = true;
                float pos = x;                  // 0..100
                if (pos < 1.0f) pos = 1.0f;     // 0 is OFF
                if (pos > 100.0f) pos = 100.0f;
                id(led_output_set_pct).publish_state((int) floorf(pos + 0.5f));
            - script.stop: ramp_off_script
            - script.stop: ramp_on_script
            - light.turn_on:
                id: mosfet_leds
                brightness: !lambda |-
                  float pos = id(led_output_set_pct).state; // 1..100
                  float minp = (float) id(min_brightness_pct);
                  float maxp = (float) id(max_brightness_pct);
                  if (maxp <= minp) maxp = minp + 1.0f;
                  float out_pct = minp + (pos * (maxp - minp) / 100.0f);
                  if (out_pct > maxp) out_pct = maxp;
                  return out_pct / 100.0f;
                transition_length: 250ms
            - lambda: 'id(ramp_switch_target_on) = true;'
            - delay: 400ms
            - lambda: 'id(suppress_slider_sync) = false;'

##########################################################################################
# SCRIPT COMPONENT
# https://esphome.io/components/script.html
# Scripts can be executed nearly anywhere in your device configuration with a single call.
##########################################################################################
script:
  # Blink pattern while ramping UP: quick double-blink, pause, repeat
  - id: led_flash_up
    mode: restart
    then:
      - while:
          condition:
            lambda: 'return true;'
          then:
            - output.turn_on: green_led_out
            - delay: 100ms
            - output.turn_off: green_led_out
            - delay: 100ms
            - output.turn_on: green_led_out
            - delay: 100ms
            - output.turn_off: green_led_out
            - delay: 400ms
  # Blink pattern while ramping DOWN: steady slow blink
  - id: led_flash_down
    mode: restart
    then:
      - while:
          condition:
            lambda: 'return true;'
          then:
            - output.turn_on: green_led_out
            - delay: 250ms
            - output.turn_off: green_led_out
            - delay: 250ms

  # Script: ramp up from current level.  Obey global max.
  - id: ramp_on_script
    mode: restart
    then:
      - script.stop: ramp_off_script
      - script.stop: led_flash_down
      - script.execute: led_flash_up
      - if:
          condition:
            lambda: |-
              const auto &cv = id(mosfet_leds).current_values;
              const float floor = id(min_brightness_pct) / 100.0f;
              return (!cv.is_on()) || (cv.get_brightness() < floor);
          then:
            - light.turn_on:
                id: mosfet_leds
                brightness: !lambda 'return id(min_brightness_pct) / 100.0f;'
                transition_length: 0s
      - light.turn_on:
          id: mosfet_leds
          brightness: !lambda 'return id(max_brightness_pct) / 100.0f;'
          transition_length: !lambda |-
            const auto &cv = id(mosfet_leds).current_values;
            const float floor = id(min_brightness_pct) / 100.0f;
            const float cap  = id(max_brightness_pct) / 100.0f;
            float curr = cv.is_on() ? cv.get_brightness() : 0.0f;
            if (curr < floor) curr = floor;
            if (curr > cap)   curr = cap;
            float frac = (cap - curr) / (cap - floor);
            if (frac < 0.0f) frac = 0.0f;
            if (frac > 1.0f) frac = 1.0f;
            id(last_ramp_ms) = (int) (id(ramp_up_ms) * frac);
            return (uint32_t) id(last_ramp_ms);
      - delay: !lambda 'return (uint32_t) id(last_ramp_ms);'
      - script.stop: led_flash_up
      - output.turn_off: green_led_out

  # Script: ramp down from current level to floor, then cleanly cut to OFF
  - id: ramp_off_script
    mode: restart
    then:
      - script.stop: ramp_on_script
      - script.stop: led_flash_up
      - script.execute: led_flash_down
      - light.turn_on:
          id: mosfet_leds
          brightness: !lambda 'return id(min_brightness_pct) / 100.0f;'
          transition_length: !lambda |-
            const auto &cv = id(mosfet_leds).current_values;
            const float floor = id(min_brightness_pct) / 100.0f;
            float curr = cv.is_on() ? cv.get_brightness() : 0.0f;
            if (curr < floor) curr = floor;
            float frac = (curr - floor) / (1.0f - floor);
            if (frac < 0.0f) frac = 0.0f;
            if (frac > 1.0f) frac = 1.0f;
            id(last_ramp_ms) = (int) (id(ramp_down_ms) * frac);
            return (uint32_t) id(last_ramp_ms);
      - delay: !lambda 'return (uint32_t) id(last_ramp_ms);'
      - light.turn_off:
          id: mosfet_leds
          transition_length: 150ms
      - delay: 150ms
      - script.stop: led_flash_down
      - output.turn_off: green_led_out
      - lambda: |-
          auto call = id(mosfet_leds).make_call();
          call.set_state(false);
          call.set_brightness(id(max_brightness_pct) / 100.0f);
          call.perform();