esphome device updates
This commit is contained in:
root
@@ -0,0 +1,482 @@
|
||||
##########################################################################################
|
||||
##########################################################################################
|
||||
# 4 Channel DMX Mains Dimmer
|
||||
# This is using an esp8366 (D1 Mini) sending DMX512 Serial to a trio of 2 channel
|
||||
# mains lighting contollers (1.2A/Channel)
|
||||
#
|
||||
# Contoller: https://www.aliexpress.com/item/32838426377.html
|
||||
# RS-485 TTL converter: https://www.aliexpress.com/item/1005005737922222.html
|
||||
#
|
||||
# V1.1 2025-09-13 Extended to 3 modules and installed
|
||||
# V1.0 2025-09-06 First Rev (only tested one module, 2 channels at this stage, and incandescent)
|
||||
##########################################################################################
|
||||
#
|
||||
# NOTES
|
||||
# ------
|
||||
# - Trialling with an incandescent bulb, 10% writes 26. Max value is 255 so this is 10%
|
||||
# - With an incandescent, I can't see any light output below about 15%
|
||||
# - Using GPIO2 as the UART TX on an ESP8266 is handy, as the onboard LED flashes with TX
|
||||
# - The dimmer needs to be set to DMX mode, and given an ID of 1-999 (not standalone or dynamic)
|
||||
# - there is no reason you can't run many dimmers off one ESP (limit may be in data speed lags?)
|
||||
# - The dimmer is pretty smooth, and it remembers values even if no data being transmitted.
|
||||
# - On my system, I am restoring all channels to ON. Power is controlled by a (smart) wallswitch
|
||||
# so if all networks fail, switching the switch will power these on and restore to full brightness.
|
||||
#
|
||||
# System Settings on Dimmer: (onboard buttons M and < held for 2 secs)
|
||||
# ------
|
||||
# - Set "1 Channel" (d-1) and both channels will output the same levels. Or "2 Channel" (d-2)
|
||||
# - Set reverse phase dimming/trailing edge (C-R) or Forward/Leading Edge (C-F)
|
||||
# - Set minimum brightness on the dimmer, from b01-b40. Min is then 5% if b01
|
||||
# - Set the 3x 8 Segment display to automatically turn off (Bon/BoF) after a period
|
||||
# - pull both DE & RE high on the 485 converter to ensure data enabled (or wire to enable_pin)
|
||||
#
|
||||
# MAX485 Module (You could also use a MAX3485 which is 3.3V)
|
||||
# ------
|
||||
# MAX485 VCC -> ESP +5V
|
||||
# MAX485 GND -> ESP GND
|
||||
# MAX485 DE -> ESP +5V
|
||||
# MAX485 RE -> Has a pullup so can leave unconnected, (or +5V)or an designated enable_pin
|
||||
# MAX485 DI -> ESP32 GPIO5 or ESP8266 GPIO2
|
||||
# MAX485 A -> XLR 3 (DMX +)
|
||||
# MAX485 B -> XLR 2 (DMX -)
|
||||
# MAX485 GND -> XLR 1 (DMX GND)
|
||||
#
|
||||
# Other useful references
|
||||
# ------
|
||||
# - Arduino DMX Controller https://www.youtube.com/watch?v=4PjBBBQB2m4
|
||||
# - ESP32 DMX Contoller with ESPixelstick (errors in his wiring diagram)
|
||||
# https://www.youtube.com/watch?v=GWZ63vsKzT8
|
||||
# - ESPHome DMX512 Custom component used here: https://github.com/andyboeh/esphome-dmx512
|
||||
# Includes good examples if you are expanding
|
||||
##########################################################################################
|
||||
##########################################################################################
|
||||
|
||||
##########################################################################################
|
||||
# SPECIFIC DEVICE VARIABLE SUBSTITUTIONS
|
||||
# If NOT using a secrets file, just replace these with the passwords etc (in quotes)
|
||||
##########################################################################################
|
||||
substitutions:
|
||||
# Device Naming
|
||||
device_name: "esp-lounge6chdimmer"
|
||||
friendly_name: "6 Channel Lounge Dimmer"
|
||||
description_comment: "Lounge 6 Channel Mains Lighting Dimmer (3 x 2 channel modules) controlled using DMX512 protocol with a D1 Mini Pro"
|
||||
device_area: "Lounge" # Allows ESP device to be automatically linked to an 'Area' in Home Assistant.
|
||||
|
||||
# Project Naming
|
||||
project_name: "Generic ESP8266.D1 Mini" # Project Details
|
||||
project_version: "v1.1" # Project V denotes release of yaml file, allowing checking of deployed vs latest version
|
||||
|
||||
# Passwords & Secrets
|
||||
api_key: !secret esp-api_key # unfortunately you can't use substitutions inside secrets names
|
||||
ota_pass: !secret esp-ota_pass # unfortunately you can't use substitutions inside secrets names
|
||||
static_ip_address: !secret esp-lounge6chdimmer_ip
|
||||
|
||||
# Device Settings
|
||||
#relay_icon: "mdi:lightbulb-group"
|
||||
log_level: "INFO" # Define logging level: NONE, ERROR, WARN, INFO, DEBUG (Default), VERBOSE, VERY_VERBOSE
|
||||
update_interval: "60s" # update time for for general sensors etc
|
||||
|
||||
output_1_name: "Lounge Downlights South"
|
||||
output_2_name: "Lounge Rafter Buttons"
|
||||
output_3_name: "Lounge Downlights Centre"
|
||||
output_4_name: "Dining Table Light"
|
||||
output_5_name: "Couch Spots Right"
|
||||
output_6_name: "Couch Spots Left"
|
||||
|
||||
# Per-channel minimum output when ON (0.00f..1.00f). OFF remains 0%.
|
||||
# Adjust per channel to avoid flicker at very low levels.
|
||||
min_output_1: "0.20f"
|
||||
min_output_2: "0.20f"
|
||||
min_output_3: "0.20f"
|
||||
min_output_4: "0.20f"
|
||||
min_output_5: "0.20f"
|
||||
min_output_6: "0.20f"
|
||||
|
||||
#########################################################################################
|
||||
# PACKAGES: Included Common Packages
|
||||
# https://esphome.io/components/packages.html
|
||||
##########################################################################################
|
||||
# Comment some of these out where not needed, eg MQTT, Web portal, SNTP, General Sensors
|
||||
##########################################################################################
|
||||
packages:
|
||||
#### WIFI, Network (Static/DHCP/IPV6 etc), Fallback AP, Safemode ####
|
||||
common_wifi: !include
|
||||
file: common/network_common.yaml
|
||||
vars:
|
||||
local_device_name: "${device_name}"
|
||||
local_static_ip_address: "${static_ip_address}"
|
||||
local_ota_pass: "${ota_pass}"
|
||||
|
||||
#### HOME ASSISTANT API (choose encryption or no encryption options) ####
|
||||
common_api: !include
|
||||
file: common/api_common.yaml
|
||||
#file: common/api_common_noencryption.yaml
|
||||
vars:
|
||||
local_api_key: "${api_key}"
|
||||
|
||||
#### MQTT ####
|
||||
common_mqtt: !include
|
||||
file: common/mqtt_common.yaml
|
||||
vars:
|
||||
local_device_name: "${device_name}"
|
||||
|
||||
#### WEB PORTAL ####
|
||||
#common_webportal: !include common/webportal_common.yaml
|
||||
#### SNTP (Only use if you want/need accurate timeclocks) ####
|
||||
common_sntp: !include common/sntp_common.yaml
|
||||
|
||||
#### DIAGNOSTICS Sensors ####
|
||||
diag_basic: !include common/include_basic_diag_sensors.yaml
|
||||
diag_more: !include common/include_more_diag_sensors.yaml
|
||||
diag_debug: !include common/include_debug_diag_sensors.yaml
|
||||
#diag_resetcount: !include common/include_resetcount_diag_sensors.yaml
|
||||
|
||||
#########################################################################################
|
||||
# ESPHome
|
||||
# https://esphome.io/components/esphome.html
|
||||
#########################################################################################
|
||||
esphome:
|
||||
name: "${device_name}"
|
||||
friendly_name: "${friendly_name}"
|
||||
comment: "${description_comment}" # Appears on the esphome page in HA
|
||||
area: "${device_area}"
|
||||
project:
|
||||
name: "${project_name}"
|
||||
version: "${project_version}"
|
||||
on_boot:
|
||||
priority: -100
|
||||
then:
|
||||
- lambda: |-
|
||||
id(dmx_ch1_sensor).publish_state(0);
|
||||
id(dmx_ch2_sensor).publish_state(0);
|
||||
id(dmx_ch3_sensor).publish_state(0);
|
||||
id(dmx_ch4_sensor).publish_state(0);
|
||||
id(dmx_ch5_sensor).publish_state(0);
|
||||
id(dmx_ch6_sensor).publish_state(0);
|
||||
|
||||
#########################################################################################
|
||||
# ESP Platform and Framework
|
||||
# https://esphome.io/components/esp32.html
|
||||
#########################################################################################
|
||||
esp8266:
|
||||
board: d1_mini_pro
|
||||
#early_pin_init: False # Initialise pins early to known values. Recommended false where switches are involved. Defaults to True.
|
||||
board_flash_mode: dout # Default is dout
|
||||
restore_from_flash: true # restore some values on reboot
|
||||
|
||||
mdns:
|
||||
disabled: false # Disabling will make the build file smaller (and it is still available via static IP)
|
||||
|
||||
#preferences:
|
||||
# flash_write_interval: 0s
|
||||
|
||||
#########################################################################################
|
||||
# ESPHome Logging Enable
|
||||
# https://esphome.io/components/logger.html
|
||||
#############################################
|
||||
logger:
|
||||
level: "${log_level}" #INFO Level suggested, or DEBUG for testing
|
||||
baud_rate: 0 #set to 0 for no logging via UART, needed if you are using it for other serial things (eg PZEM)
|
||||
#esp8266_store_log_strings_in_flash: false
|
||||
#tx_buffer_size: 64
|
||||
|
||||
#########################################################################################
|
||||
# STATUS LED
|
||||
# https://esphome.io/components/status_led.html
|
||||
#########################################################################################
|
||||
#status_led:
|
||||
# pin:
|
||||
# number: GPIO2
|
||||
# inverted: yes
|
||||
|
||||
#########################################################################################
|
||||
# UART COMPONENT
|
||||
# https://esphome.io/components/uart/
|
||||
#########################################################################################
|
||||
uart:
|
||||
# Needed for the DMX component.
|
||||
# This UART talks to the RS485 adaptor
|
||||
# There is no receiving, it is a one way send
|
||||
id: uart_bus
|
||||
baud_rate: 250000
|
||||
tx_pin:
|
||||
number: GPIO2 #ESP8266
|
||||
allow_other_uses: true # For ESPHome >= 2023.12.0
|
||||
stop_bits: 2
|
||||
|
||||
##########################################################################################
|
||||
# LIGHT COMPONENT
|
||||
# https://esphome.io/components/light/
|
||||
##########################################################################################
|
||||
light:
|
||||
- platform: monochromatic
|
||||
name: ${output_1_name}
|
||||
output: dmx_1
|
||||
id: light_test_1
|
||||
default_transition_length: 10s
|
||||
gamma_correct: 2.2
|
||||
restore_mode: ALWAYS_ON
|
||||
- platform: monochromatic
|
||||
name: ${output_2_name}
|
||||
output: dmx_2
|
||||
id: light_test_2
|
||||
default_transition_length: 10s
|
||||
gamma_correct: 2.2
|
||||
restore_mode: ALWAYS_ON
|
||||
- platform: monochromatic
|
||||
name: ${output_3_name}
|
||||
output: dmx_3
|
||||
id: light_test_3
|
||||
default_transition_length: 10s
|
||||
gamma_correct: 2.2
|
||||
restore_mode: ALWAYS_ON
|
||||
- platform: monochromatic
|
||||
name: ${output_4_name}
|
||||
output: dmx_4
|
||||
id: light_test_4
|
||||
default_transition_length: 10s
|
||||
gamma_correct: 1
|
||||
restore_mode: ALWAYS_ON
|
||||
- platform: monochromatic
|
||||
name: ${output_5_name}
|
||||
output: dmx_5
|
||||
id: light_test_5
|
||||
default_transition_length: 10s
|
||||
gamma_correct: 1
|
||||
restore_mode: RESTORE_DEFAULT_OFF
|
||||
- platform: monochromatic
|
||||
name: ${output_6_name}
|
||||
output: dmx_6
|
||||
id: light_test_6
|
||||
default_transition_length: 10s
|
||||
gamma_correct: 1
|
||||
restore_mode: RESTORE_DEFAULT_OFF
|
||||
|
||||
##########################################################################################
|
||||
# SENSOR COMPONENT
|
||||
# https://esphome.io/components/sensor/
|
||||
##########################################################################################
|
||||
sensor:
|
||||
# Expose each DMX channel's current output level as 0..255 integers (post-gamma)
|
||||
- platform: template
|
||||
id: dmx_ch1_sensor
|
||||
name: ${output_1_name} Output
|
||||
icon: mdi:counter
|
||||
#entity_category: diagnostic
|
||||
accuracy_decimals: 0
|
||||
update_interval: never
|
||||
filters:
|
||||
- throttle: 200ms
|
||||
- delta: 1
|
||||
- round: 0
|
||||
- clamp:
|
||||
min_value: 0
|
||||
max_value: 255
|
||||
|
||||
- platform: template
|
||||
id: dmx_ch2_sensor
|
||||
name: ${output_2_name} Output
|
||||
icon: mdi:counter
|
||||
#entity_category: diagnostic
|
||||
accuracy_decimals: 0
|
||||
update_interval: never
|
||||
filters:
|
||||
- throttle: 200ms
|
||||
- delta: 1
|
||||
- round: 0
|
||||
- clamp:
|
||||
min_value: 0
|
||||
max_value: 255
|
||||
|
||||
- platform: template
|
||||
id: dmx_ch3_sensor
|
||||
name: ${output_3_name} Output
|
||||
icon: mdi:counter
|
||||
#entity_category: diagnostic
|
||||
accuracy_decimals: 0
|
||||
update_interval: never
|
||||
filters:
|
||||
- throttle: 200ms
|
||||
- delta: 1
|
||||
- round: 0
|
||||
- clamp:
|
||||
min_value: 0
|
||||
max_value: 255
|
||||
|
||||
- platform: template
|
||||
id: dmx_ch4_sensor
|
||||
name: ${output_4_name} Output
|
||||
icon: mdi:counter
|
||||
#entity_category: diagnostic
|
||||
accuracy_decimals: 0
|
||||
update_interval: never
|
||||
filters:
|
||||
- throttle: 200ms
|
||||
- delta: 1
|
||||
- round: 0
|
||||
- clamp:
|
||||
min_value: 0
|
||||
max_value: 255
|
||||
|
||||
- platform: template
|
||||
id: dmx_ch5_sensor
|
||||
name: ${output_5_name} Output
|
||||
icon: mdi:counter
|
||||
#entity_category: diagnostic
|
||||
accuracy_decimals: 0
|
||||
update_interval: never
|
||||
filters:
|
||||
- throttle: 200ms
|
||||
- delta: 1
|
||||
- round: 0
|
||||
- clamp:
|
||||
min_value: 0
|
||||
max_value: 255
|
||||
|
||||
- platform: template
|
||||
id: dmx_ch6_sensor
|
||||
name: ${output_6_name} Output
|
||||
icon: mdi:counter
|
||||
#entity_category: diagnostic
|
||||
accuracy_decimals: 0
|
||||
update_interval: never
|
||||
filters:
|
||||
- throttle: 200ms
|
||||
- delta: 1
|
||||
- round: 0
|
||||
- clamp:
|
||||
min_value: 0
|
||||
max_value: 255
|
||||
|
||||
##########################################################################################
|
||||
# CUSTOM COMPONENT DMX512
|
||||
# https://github.com/andyboeh/esphome-dmx512
|
||||
##########################################################################################
|
||||
external_components:
|
||||
- source: github://andyboeh/esphome-dmx512
|
||||
|
||||
dmx512:
|
||||
id: dmx
|
||||
uart_id: uart_bus
|
||||
#enable_pin: GPIOXX (Optional, I've wire them to be always active)
|
||||
tx_pin:
|
||||
number: GPIO2
|
||||
allow_other_uses: true # For ESPHome >= 2023.12.0
|
||||
uart_num: 1
|
||||
periodic_update: true # optional. Some dimmers may turn off without regular updates.
|
||||
#force_full_frames: false # optional. If true the 513 byte is always sent
|
||||
#custom_break_len: 92 # optional. Break Length. Default is 92uS
|
||||
#custom_mab_len: 12 # optional. Mark after Break Length. Default is 12mS
|
||||
#update_interval: 500 # optional. Custom update interval. Default is 500mS
|
||||
|
||||
##########################################################################################
|
||||
# OUTPUT COMPONENT
|
||||
# https://esphome.io/components/output/ledc.html
|
||||
##########################################################################################
|
||||
output:
|
||||
# Raw DMX slots (these are the actual DMX universes/slots)
|
||||
- platform: dmx512
|
||||
channel: 1 # The ID we set the device to
|
||||
universe: dmx # The ID of the DMX512 Component
|
||||
id: dmx_1_raw
|
||||
- platform: dmx512
|
||||
channel: 2 # The ID we set the device to
|
||||
universe: dmx # The ID of the DMX512 Component
|
||||
id: dmx_2_raw
|
||||
- platform: dmx512
|
||||
channel: 3 # The ID we set the device to
|
||||
universe: dmx # The ID of the DMX512 Component
|
||||
id: dmx_3_raw
|
||||
- platform: dmx512
|
||||
channel: 4 # The ID we set the device to
|
||||
universe: dmx # The ID of the DMX512 Component
|
||||
id: dmx_4_raw
|
||||
- platform: dmx512
|
||||
channel: 5 # The ID we set the device to
|
||||
universe: dmx # The ID of the DMX512 Component
|
||||
id: dmx_5_raw
|
||||
- platform: dmx512
|
||||
channel: 6 # The ID we set the device to
|
||||
universe: dmx # The ID of the DMX512 Component
|
||||
id: dmx_6_raw
|
||||
|
||||
# Wrapped outputs: publish exact 0..255 to sensors, then forward float to raw DMX
|
||||
- platform: template
|
||||
id: dmx_1
|
||||
type: float
|
||||
write_action:
|
||||
- lambda: |-
|
||||
const float MIN = ${min_output_1};
|
||||
float scaled = state;
|
||||
if (state > 0.0f) {
|
||||
// Remap 0..1 -> MIN..1.0 (keep OFF at 0)
|
||||
scaled = state * (1.0f - MIN) + MIN;
|
||||
}
|
||||
id(dmx_ch1_sensor).publish_state(scaled * 255.0f);
|
||||
id(dmx_1_raw).set_level(scaled);
|
||||
|
||||
- platform: template
|
||||
id: dmx_2
|
||||
type: float
|
||||
write_action:
|
||||
- lambda: |-
|
||||
const float MIN = ${min_output_2};
|
||||
float scaled = state;
|
||||
if (state > 0.0f) {
|
||||
scaled = state * (1.0f - MIN) + MIN;
|
||||
}
|
||||
id(dmx_ch2_sensor).publish_state(scaled * 255.0f);
|
||||
id(dmx_2_raw).set_level(scaled);
|
||||
|
||||
- platform: template
|
||||
id: dmx_3
|
||||
type: float
|
||||
write_action:
|
||||
- lambda: |-
|
||||
const float MIN = ${min_output_3};
|
||||
float scaled = state;
|
||||
if (state > 0.0f) {
|
||||
scaled = state * (1.0f - MIN) + MIN;
|
||||
}
|
||||
id(dmx_ch3_sensor).publish_state(scaled * 255.0f);
|
||||
id(dmx_3_raw).set_level(scaled);
|
||||
|
||||
- platform: template
|
||||
id: dmx_4
|
||||
type: float
|
||||
write_action:
|
||||
- lambda: |-
|
||||
const float MIN = ${min_output_4};
|
||||
float scaled = state;
|
||||
if (state > 0.0f) {
|
||||
scaled = state * (1.0f - MIN) + MIN;
|
||||
}
|
||||
id(dmx_ch4_sensor).publish_state(scaled * 255.0f);
|
||||
id(dmx_4_raw).set_level(scaled);
|
||||
|
||||
- platform: template
|
||||
id: dmx_5
|
||||
type: float
|
||||
write_action:
|
||||
- lambda: |-
|
||||
const float MIN = ${min_output_5};
|
||||
float scaled = state;
|
||||
if (state > 0.0f) {
|
||||
scaled = state * (1.0f - MIN) + MIN;
|
||||
}
|
||||
id(dmx_ch5_sensor).publish_state(scaled * 255.0f);
|
||||
id(dmx_5_raw).set_level(scaled);
|
||||
|
||||
- platform: template
|
||||
id: dmx_6
|
||||
type: float
|
||||
write_action:
|
||||
- lambda: |-
|
||||
const float MIN = ${min_output_6};
|
||||
float scaled = state;
|
||||
if (state > 0.0f) {
|
||||
scaled = state * (1.0f - MIN) + MIN;
|
||||
}
|
||||
id(dmx_ch6_sensor).publish_state(scaled * 255.0f);
|
||||
id(dmx_6_raw).set_level(scaled);
|
||||
|
||||
Reference in New Issue
Block a user