weather station esphome updates

esphome/trash/esp-mmwave-office-7776ec.yaml

@@ -1,370 +0,0 @@
-# https://digiblur.com/2023/05/24/esphome-mmwave-presence-how-to-guide/
-
-substitutions:
-  name: esp-mmwave-office-7776ec
-  friendly_name: esp-mmwave-office
-  update_time: 30s
-
-esphome:
-  name: ${name}
-  friendly_name: ${friendly_name}
-  name_add_mac_suffix: false
-  #project:
-    #name: esphome.web
-    #version: '1.0'
-  on_boot:    #LD1125H Initial Setting
-    priority: -200
-    then:
-      - uart.write:
-          id: LD1125H_UART_BUS
-          data: !lambda |-
-            std::string th1st = "mth1=" + str_sprintf("%.0f",id(LD1125H_mth1).state) +"\r\n";
-            return std::vector<uint8_t>(th1st.begin(), th1st.end());
-      - uart.write:
-          id: LD1125H_UART_BUS
-          data: !lambda |-
-            std::string th2st = "mth2=" + str_sprintf("%.0f",id(LD1125H_mth2).state) +"\r\n";
-            return std::vector<uint8_t>(th2st.begin(), th2st.end());
-      - uart.write:
-          id: LD1125H_UART_BUS
-          data: !lambda |-
-            std::string th3st = "mth3=" + str_sprintf("%.0f",id(LD1125H_mth3).state) +"\r\n";
-            return std::vector<uint8_t>(th3st.begin(), th3st.end());
-      - uart.write:
-          id: LD1125H_UART_BUS
-          data: !lambda |-
-            std::string rmaxst = "rmax=" + str_sprintf("%.1f",id(LD1125H_rmax).state) +"\r\n";
-            return std::vector<uint8_t>(rmaxst.begin(), rmaxst.end());
-
-
-
-#############################################    
-# ESPHome Logging Enable
-############################################# 
-# NOTE: Baudrate set to 0 as we are using the UART with PZEM
-logger:
-  level: INFO  #You Can Use "INFO" Level
-  baud_rate: 0
-
-#############################################    
-# Enable the Home Assistant API
-#############################################  
-api:
-  #encryption:
-  #  key: !secret esp-mainovenmonitor_api_key
-
-#############################################    
-# Enable Over the Air Update Capability
-# Safe mode will detect boot loops
-#############################################  
-ota:
- # safe_mode: true
- # password: !secret esp-mainovenmonitor_ota_pass
-
-#############################################    
-# Use Wifi 
-#############################################  
-wifi:
-  ssid: !secret wifi_ssid
-  password: !secret wifi_password
-  power_save_mode: LIGHT
-  # Details for fallback hotspot (captive portal) 
-  # in case wifi connection fails
-  ap:
-    ssid: "MMwave Office Fallback Hotspot"
-    password: !secret fallback_ap_password
-#  manual_ip:
-#    static_ip: 192.168.x.x
-#    gateway: 192.168.X.x
-#    subnet: 255.255.255.0
-
-
-# Allow provisioning Wi-Fi via serial
-#improv_serial:
-
-#############################################    
-# Fallback captive portal
-#############################################   
-# In combination with the `ap` this allows the user
-# to provision wifi credentials to the device via WiFi AP.
-captive_portal:
-
-#dashboard_import:
-#  package_import_url: github://esphome/example-configs/esphome-web/esp32.yaml@main
-#  import_full_config: true
-
-# Sets up Bluetooth LE (Only on ESP32) to allow the user
-# to provision wifi credentials to the device.
-##esp32_improv:
-##  authorizer: none
-
-#############################################    
-# Web Portal for display and monitoring
-#############################################   
-#web_server:
-#  port: 80
-#  auth:
-#    username: !secret web_server_username
-#    password: !secret web_server_password
-
-
-i2c:
-  sda: GPIO19
-  scl: GPIO21
-  scan: True  
-
-#esp32:
-#  board: esp32dev
-#  framework:
-#    type: arduino
-esp32:
-  board: nodemcu-32s
-  framework:
-    type: esp-idf  #Suggest Use ESP-IDF Framework, or Plug Out the UART Cable Might Cause ESP32 Hang. 
-
-external_components:
-  - source:
-      type: git
-      url: https://github.com/ssieb/custom_components #Thanks for @ssieb components.
-    components: [ serial ]
-
-
-uart:
-  id: LD1125H_UART_BUS
-  rx_pin: GPIO16  #For ESP32, you can use any pin, Recommend Use UART_2, Don't use UART_0, It might Cause Boot Fail or System Hang
-  tx_pin: GPIO17  #For ESP32, you can use any pin, Recommend Use UART_2, Don't use UART_0, It might Cause Boot Fail or System Hang
-#  rx_pin: GPIO1  #For ESP32, you can use any pin, Recommend Use UART_2, Don't use UART_0, It might Cause Boot Fail or System Hang
-#  tx_pin: GPIO0 #For ESP32, you can use any pin, Recommend Use UART_2, Don't use UART_0, It might Cause Boot Fail or System Hang
-  baud_rate: 115200
-  data_bits: 8
-  stop_bits: 1
-  parity: NONE
-#  debug:
-#    direction: BOTH
-#    dummy_receiver: false
-#    after:
-#      delimiter: "\n"
-#    sequence:
-#      - lambda: UARTDebug::log_string(direction, bytes);
-globals:
-  - id: LD1125H_Last_Time
-    type: time_t
-    restore_value: no
-    initial_value: time(NULL)
-  - id: LD1125H_Last_Mov_Time
-    type: time_t
-    restore_value: no
-    initial_value: time(NULL)
-  - id: LD1125H_Clearence_Status
-    type: bool
-    restore_value: no
-    initial_value: "false"
-status_led:
-  pin:
-    number: GPIO2 #ESP32 OnBroad LED
-    inverted: false
-#web_server:   #Avoid Using Web Server To Prevent Hang
-#  port: 80
-interval:
-  - interval: 1s #Clearance Scan Time
-    setup_priority: -200
-    then:
-      lambda: |-
-        if ((time(NULL)-id(LD1125H_Last_Time))>id(LD1125H_Clear_Time).state) {
-          if ((id(LD1125H_Clearence_Status) == false) || (id(LD1125H_Occupancy).state != "Clearance")) {
-            id(LD1125H_Occupancy).publish_state("Clearance");
-            id(LD1125H_Clearence_Status) = true;
-          }
-          if (id(LD1125H_MovOcc_Binary).state == true) {
-            id(LD1125H_MovOcc_Binary).publish_state(false);
-          }
-          if (id(LD1125H_Mov_Binary).state == true) {
-            id(LD1125H_Mov_Binary).publish_state(false);
-          }
-        }
-number:
-  - platform: template
-    name: ${upper_devicename} LD1125H mth1 #mth1 is 0~2.8m Sensitivity.
-    id: LD1125H_mth1
-    icon: "mdi:cogs"
-    optimistic: true
-    restore_value: true #If you don't want to store the setting at ESP, set it to false.
-    initial_value: "60.0" #Default mth1 Setting
-    min_value: 10.0
-    max_value: 600.0
-    step: 5.0
-    set_action:
-      then:
-        - uart.write:
-            id: LD1125H_UART_BUS
-            data: !lambda |-
-              std::string th1st = "mth1=" + str_sprintf("%.0f",x) +"\r\n";
-              return std::vector<uint8_t>(th1st.begin(), th1st.end());
-  - platform: template
-    name: ${upper_devicename} LD1125H mth2 #mth2 is 2.8~8m Sensitivity.
-    id: LD1125H_mth2
-    icon: "mdi:cogs"
-    optimistic: true
-    restore_value: true #If you don't want to store the setting at ESP, set it to false.
-    initial_value: "30" #Default mth2 Setting
-    min_value: 5
-    max_value: 300
-    step: 5
-    set_action:
-      then:
-        - uart.write:
-            id: LD1125H_UART_BUS
-            data: !lambda |-
-              std::string th2st = "mth2=" + str_sprintf("%.0f",x) +"\r\n";
-              return std::vector<uint8_t>(th2st.begin(), th2st.end());
-  - platform: template
-    name: ${upper_devicename} LD1125H mth3 #mth3 is above 8m Sensitivity.
-    id: LD1125H_mth3
-    icon: "mdi:cogs"
-    optimistic: true
-    restore_value: true #If you don't want to store the setting at ESP, set it to false.
-    initial_value: "20" #Default mth3 Setting
-    min_value: 5
-    max_value: 200
-    step: 5
-    set_action:
-      then:
-        - uart.write:
-            id: LD1125H_UART_BUS
-            data: !lambda |-
-              std::string th3st = "mth3=" + str_sprintf("%.0f",x) +"\r\n";
-              return std::vector<uint8_t>(th3st.begin(), th3st.end());
-  - platform: template
-    name: ${upper_devicename} LD1125H rmax #rmax is max detection distance.
-    id: LD1125H_rmax
-    icon: "mdi:cogs"
-    optimistic: true
-    restore_value: true #If you don't want to store the setting at ESP, set it to false.
-    initial_value: "8" #Default rmax Setting
-    min_value: 0.4
-    max_value: 12
-    step: 0.1
-    set_action:
-      then:
-        - uart.write:
-            id: LD1125H_UART_BUS
-            data: !lambda |-
-              std::string rmaxst = "rmax=" + str_sprintf("%.1f",x) +"\r\n";
-              return std::vector<uint8_t>(rmaxst.begin(), rmaxst.end());
-  - platform: template
-    name: ${upper_devicename} LD1125H Clearence Time
-    id: LD1125H_Clear_Time
-    icon: "mdi:cogs"
-    optimistic: true
-    restore_value: true #If you don't want to store the setting at ESP, set it to false.
-    initial_value: "5" #LD1125H Mov/Occ > Clearence Time Here
-    min_value: 0.5
-    max_value: 20
-    step: 0.5
-  - platform: template
-    name: ${upper_devicename} LD1125H Movement Time
-    id: LD1125H_Mov_Time
-    icon: "mdi:cogs"
-    optimistic: true
-    restore_value: true #If you don't want to store the setting at ESP, set it to false.
-    initial_value: "1" #LD1125H Mov > Occ Time Here
-    min_value: 0.5
-    max_value: 10
-    step: 0.5
-sensor:
-  - platform: bme280_i2c
-    temperature:
-      name: ${upper_devicename} BME280 Temp
-      accuracy_decimals: 1     
-      oversampling: 2x
-    pressure:
-      name: ${upper_devicename} BME280 Pressure
-      oversampling: 2x
-    humidity:
-      name: ${upper_devicename} BME280 Humidity
-      accuracy_decimals: 1     
-      oversampling: 2x
-    address: 0x76
-    update_interval: ${update_time}   
-#  - platform: aht10
-#    temperature:
-#      accuracy_decimals: 2     
-#      name: ${upper_devicename} AHT21 Temp
-#    humidity:
-#      accuracy_decimals: 2     
-#      name: ${upper_devicename} AHT21 Humidity
-#    update_interval: ${update_time}     
-#  - platform: wifi_signal
-#    name: ${upper_devicename} WiFi Signal
-#    update_interval: 60s
-  - platform: uptime
-    name: ${upper_devicename} Uptime
-  - platform: template
-    name: ${upper_devicename} LD1125H Distance
-    id: LD1125H_Distance
-    icon: "mdi:signal-distance-variant"
-    unit_of_measurement: "m"
-    accuracy_decimals: 2
-    filters:    # Use Fliter To Debounce
-    - sliding_window_moving_average:
-        window_size: 8
-        send_every: 2
-    - heartbeat: 0.2s
-text_sensor:
-  - platform: serial
-    uart_id: LD1125H_UART_BUS
-    name: ${upper_devicename} LD1125H UART Text
-    id: LD1125H_UART_Text
-    icon: "mdi:format-text"
-    internal: True #If Don't Want to See UART Receive Data, Set To True
-    on_value:
-      lambda: |-
-        if (id(LD1125H_UART_Text).state.substr(0,3) == "occ") {
-          id(LD1125H_Distance).publish_state(atof(id(LD1125H_UART_Text).state.substr(9).c_str()));
-          if ((time(NULL)-id(LD1125H_Last_Mov_Time))>id(LD1125H_Mov_Time).state) {
-            id(LD1125H_Occupancy).publish_state("Occupancy");
-            if (id(LD1125H_MovOcc_Binary).state == false) {
-              id(LD1125H_MovOcc_Binary).publish_state(true);
-            }
-            if (id(LD1125H_Mov_Binary).state == true) {
-              id(LD1125H_Mov_Binary).publish_state(false);
-            }
-          }
-          if (id(LD1125H_MovOcc_Binary).state == false) {
-            id(LD1125H_MovOcc_Binary).publish_state(true);
-          }
-          id(LD1125H_Last_Time) = time(NULL);
-          if (id(LD1125H_Clearence_Status) == true) {
-            id(LD1125H_Clearence_Status) = false;
-          }
-        }
-        else if (id(LD1125H_UART_Text).state.substr(0,3) == "mov") {
-          id(LD1125H_Distance).publish_state(atof(id(LD1125H_UART_Text).state.substr(9).c_str()));
-          id(LD1125H_Occupancy).publish_state("Movement");
-          if (id(LD1125H_MovOcc_Binary).state == false) {
-            id(LD1125H_MovOcc_Binary).publish_state(true);
-          }
-          if (id(LD1125H_Mov_Binary).state == false) {
-            id(LD1125H_Mov_Binary).publish_state(true);
-          }
-          id(LD1125H_Last_Mov_Time) = time(NULL);
-          id(LD1125H_Last_Time) = time(NULL);
-          if (id(LD1125H_Clearence_Status) == true) {
-            id(LD1125H_Clearence_Status) = false;
-          }
-        }
-  - platform: template
-    name: ${upper_devicename} LD1125H Occupancy Status
-    id: LD1125H_Occupancy
-    icon: "mdi:motion-sensor"
-binary_sensor:
-  - platform: status
-    name: ${upper_devicename} Status
-  - platform: template
-    name: ${upper_devicename} LD1125H Occupancy or Movement
-    id: LD1125H_MovOcc_Binary
-    device_class: occupancy
-  - platform: template
-    name: ${upper_devicename} LD1125H Movement
-    id: LD1125H_Mov_Binary
-    device_class: motion  

esphome/trash/esp-mmwave-office.yaml

@@ -1,31 +0,0 @@
-esphome:
-  name: esp-mmwave-office
-  friendly_name: esp-mmwave-office
-
-esp32:
-  board: esp32dev
-  framework:
-    type: arduino
-
-# Enable logging
-logger:
-
-# Enable Home Assistant API
-api:
-  encryption:
-    key: "KbgRoOmslFkhfRnWgr3RKK6P3Ed3dhHJ+l9FVYZX8lo="
-
-ota:
-  password: "b3a0a1de8ea89ebf360fbeac40af7a0a"
-
-wifi:
-  ssid: !secret wifi_ssid
-  password: !secret wifi_password
-
-  # Enable fallback hotspot (captive portal) in case wifi connection fails
-  ap:
-    ssid: "Esp-Mmwave-Office"
-    password: "EsNR8kqAOUu8"
-
-captive_portal:
-    

esphome/trash/esp-mmwaveoffice-7776ec.yaml

@@ -1,401 +0,0 @@
-#############################################
-# Variable Substitutions
-#############################################
-substitutions:
-  devicename: "esp-mmwaveoffice-7776ec"
-  friendly_name: "Office Occupancy"
-  mqtt_topic: "esphome"
-  update_time: 30s #for temp sensors etc
-
-#############################################
-# ESPHome
-# https://esphome.io/components/esphome.html
-#############################################
-esphome:
-  name: ${devicename}
-  comment: D1 Mini ESP32 with mmWave and environment sensors for main office #appears on the esphome page in HA
-  on_boot:    #LD1125H Initial Setting
-    priority: -200
-    then:
-      - uart.write:
-          id: LD1125H_UART_BUS
-          data: !lambda |-
-            std::string th1st = "mth1=" + str_sprintf("%.0f",id(LD1125H_mth1).state) +"\r\n";
-            return std::vector<uint8_t>(th1st.begin(), th1st.end());
-      - uart.write:
-          id: LD1125H_UART_BUS
-          data: !lambda |-
-            std::string th2st = "mth2=" + str_sprintf("%.0f",id(LD1125H_mth2).state) +"\r\n";
-            return std::vector<uint8_t>(th2st.begin(), th2st.end());
-      - uart.write:
-          id: LD1125H_UART_BUS
-          data: !lambda |-
-            std::string th3st = "mth3=" + str_sprintf("%.0f",id(LD1125H_mth3).state) +"\r\n";
-            return std::vector<uint8_t>(th3st.begin(), th3st.end());
-      - uart.write:
-          id: LD1125H_UART_BUS
-          data: !lambda |-
-            std::string rmaxst = "rmax=" + str_sprintf("%.1f",id(LD1125H_rmax).state) +"\r\n";
-            return std::vector<uint8_t>(rmaxst.begin(), rmaxst.end());
-
-#############################################
-# ESP Platform and Framework
-# https://esphome.io/components/esp32.html
-#############################################
-esp32:
-  board: nodemcu-32s
-  framework:
-    type: arduino
-    #type: esp-idf  #Suggested Use ESP-IDF Framework, or Plug Out the UART Cable Might Cause ESP32 Hang. 
-    version: recommended #recommended, latest or dev
-
-#############################################
-# i2s bus
-# https://esphome.io/components/i2c.html
-#############################################
-i2c:
-  sda: GPIO19
-  scl: GPIO21
-  scan: True  
-  frequency: 100kHz #10, 50, 100, 200, 800 are possible settings, 100kHz was reliable for me
-
-#############################################    
-# ESPHome external or custom components to use
-# https://esphome.io/components/external_components.html
-############################################# 
-external_components:
-  - source:
-      type: git
-      url: https://github.com/ssieb/custom_components #Thanks for @ssieb components.
-    components: [ serial ]  #text_sensor that reads lines for a uart. Also, a sensor that reads single values from the uart.
-
-#############################################    
-# ESPHome Logging Enable
-# https://esphome.io/components/logger.html
-############################################# 
-logger:
-  level: INFO  #INFO Level suggested, or DEBUG for testing
-  baud_rate: 0 #set to 0 for no logging via UART, needed if you are using it for other serial things (eg PZEM)
-  #esp8266_store_log_strings_in_flash: false
-  #tx_buffer_size: 64
-
-#############################################    
-# Enable the Home Assistant API
-# https://esphome.io/components/api.html
-#############################################  
-api:
-  encryption:
-    key: !secret esp-mmwaveoffice_api_key
-
-#############################################    
-# Enable Over the Air Update Capability
-# Safe mode will detect boot loops
-# https://esphome.io/components/ota.html?highlight=ota
-#############################################  
-ota:
-  safe_mode: true
-  password: !secret esp-mmwaveoffice_ota_pass
-
-#############################################    
-# Wifi Settings 
-# https://esphome.io/components/wifi.html
-#############################################  
-wifi:
-  ssid: !secret wifi_ssid
-  password: !secret wifi_password
-  #power_save_mode: LIGHT #https://esphome.io/components/wifi.html#wifi-power-save-mode
-  #manual_ip:
-    #static_ip: 192.168.x.x
-    #gateway: 192.168.X.x
-    #subnet: 255.255.255.0
-  #ap:   #Details for fallback hotspot (captive portal) in case wifi connection fails
-    #ssid: "? Fallback Hotspot"
-    #password: !secret fallback_ap_password
-
-#############################################    
-# Web Portal for display and monitoring
-# Turning this off is probably a good idea to save resources.
-# https://esphome.io/components/web_server.html
-#############################################   
-web_server:
-  port: 80
-#   username: !secret web_server_username
-#    password: !secret web_server_password
-
-#############################################
-# MQTT Monitoring
-# https://esphome.io/components/mqtt.html?highlight=mqtt
-# MUST also have api enabled if you enable MQTT
-#############################################
-mqtt:
-  broker: !secret mqtt_server
-  topic_prefix: ${mqtt_topic}/${devicename}
-  username: !secret mqtt_username
-  password: !secret mqtt_password
-
-#############################################
-# UART Serial
-# hardware on EPS32, but software, and can be glitchy on ESP8266
-# https://esphome.io/components/uart.html?highlight=uart
-#############################################
-uart:
-  id: LD1125H_UART_BUS
-  rx_pin: GPIO16  #For ESP32, you can use any pin, Recommend Use UART_2, Don't use UART_0, It might Cause Boot Fail or System Hang
-  tx_pin: GPIO17  #For ESP32, you can use any pin, Recommend Use UART_2, Don't use UART_0, It might Cause Boot Fail or System Hang
-#  rx_pin: GPIO1  #For ESP32, you can use any pin, Recommend Use UART_2, Don't use UART_0, It might Cause Boot Fail or System Hang
-#  tx_pin: GPIO0 #For ESP32, you can use any pin, Recommend Use UART_2, Don't use UART_0, It might Cause Boot Fail or System Hang
-  baud_rate: 115200
-  data_bits: 8
-  stop_bits: 1
-  parity: NONE
-#  debug:
-#    direction: BOTH
-#    dummy_receiver: false
-#    after:
-#      delimiter: "\n"
-#    sequence:
-#      - lambda: UARTDebug::log_string(direction, bytes);
-
-#############################################
-# Global Variables for use in automations etc
-# https://esphome.io/guides/automations.html?highlight=globals#global-variables
-#############################################
-globals:
-  - id: LD1125H_Last_Time
-    type: time_t
-    restore_value: no
-    initial_value: time(NULL)
-  - id: LD1125H_Last_Mov_Time
-    type: time_t
-    restore_value: no
-    initial_value: time(NULL)
-  - id: LD1125H_Clearence_Status
-    type: bool
-    restore_value: no
-    initial_value: "false"
-
-#############################################
-# General esp status LED
-# https://esphome.io/components/status_led.html
-#############################################
-status_led:
-  pin:
-    number: GPIO2 #ESP32 Onboard LED
-    inverted: false
-
-#############################################
-# Interval Automations 
-# https://esphome.io/guides/automations.html       
-#############################################
-interval:
-  - interval: 1s #Clearance Scan Time
-    setup_priority: -200
-    then:
-      lambda: |-
-        if ((time(NULL)-id(LD1125H_Last_Time))>id(LD1125H_Clear_Time).state) {
-          if ((id(LD1125H_Clearence_Status) == false) || (id(LD1125H_Occupancy).state != "Clearance")) {
-            id(LD1125H_Occupancy).publish_state("Clearance");
-            id(LD1125H_Clearence_Status) = true;
-          }
-          if (id(LD1125H_MovOcc_Binary).state == true) {
-            id(LD1125H_MovOcc_Binary).publish_state(false);
-          }
-          if (id(LD1125H_Mov_Binary).state == true) {
-            id(LD1125H_Mov_Binary).publish_state(false);
-          }
-        }
-
-#############################################
-# Number Sensors (custom component)        
-# refer https://github.com/ssieb/esphome_components/tree/master/components/serial
-#############################################
-number:
-  - platform: template
-    name: ${friendly_name} LD1125H mth1 #mth1 is 0~2.8m Sensitivity.
-    id: LD1125H_mth1
-    icon: "mdi:cogs"
-    optimistic: true
-    restore_value: true #If you don't want to store the setting at ESP, set it to false.
-    initial_value: "60.0" #Default mth1 Setting
-    min_value: 10.0
-    max_value: 600.0
-    step: 5.0
-    set_action:
-      then:
-        - uart.write:
-            id: LD1125H_UART_BUS
-            data: !lambda |-
-              std::string th1st = "mth1=" + str_sprintf("%.0f",x) +"\r\n";
-              return std::vector<uint8_t>(th1st.begin(), th1st.end());
-  - platform: template
-    name: ${friendly_name} LD1125H mth2 #mth2 is 2.8~8m Sensitivity.
-    id: LD1125H_mth2
-    icon: "mdi:cogs"
-    optimistic: true
-    restore_value: true #If you don't want to store the setting at ESP, set it to false.
-    initial_value: "30" #Default mth2 Setting
-    min_value: 5
-    max_value: 300
-    step: 5
-    set_action:
-      then:
-        - uart.write:
-            id: LD1125H_UART_BUS
-            data: !lambda |-
-              std::string th2st = "mth2=" + str_sprintf("%.0f",x) +"\r\n";
-              return std::vector<uint8_t>(th2st.begin(), th2st.end());
-  - platform: template
-    name: ${friendly_name} LD1125H mth3 #mth3 is above 8m Sensitivity.
-    id: LD1125H_mth3
-    icon: "mdi:cogs"
-    optimistic: true
-    restore_value: true #If you don't want to store the setting at ESP, set it to false.
-    initial_value: "20" #Default mth3 Setting
-    min_value: 5
-    max_value: 200
-    step: 5
-    set_action:
-      then:
-        - uart.write:
-            id: LD1125H_UART_BUS
-            data: !lambda |-
-              std::string th3st = "mth3=" + str_sprintf("%.0f",x) +"\r\n";
-              return std::vector<uint8_t>(th3st.begin(), th3st.end());
-  - platform: template
-    name: ${friendly_name} LD1125H rmax #rmax is max detection distance.
-    id: LD1125H_rmax
-    icon: "mdi:cogs"
-    optimistic: true
-    restore_value: true #If you don't want to store the setting at ESP, set it to false.
-    initial_value: "8" #Default rmax Setting
-    min_value: 0.4
-    max_value: 12
-    step: 0.1
-    set_action:
-      then:
-        - uart.write:
-            id: LD1125H_UART_BUS
-            data: !lambda |-
-              std::string rmaxst = "rmax=" + str_sprintf("%.1f",x) +"\r\n";
-              return std::vector<uint8_t>(rmaxst.begin(), rmaxst.end());
-  - platform: template
-    name: ${friendly_name} LD1125H Clearence Time
-    id: LD1125H_Clear_Time
-    icon: "mdi:cogs"
-    optimistic: true
-    restore_value: true #If you don't want to store the setting at ESP, set it to false.
-    initial_value: "5" #LD1125H Mov/Occ > Clearence Time Here
-    min_value: 0.5
-    max_value: 20
-    step: 0.5
-  - platform: template
-    name: ${friendly_name} LD1125H Movement Time
-    id: LD1125H_Mov_Time
-    icon: "mdi:cogs"
-    optimistic: true
-    restore_value: true #If you don't want to store the setting at ESP, set it to false.
-    initial_value: "1" #LD1125H Mov > Occ Time Here
-    min_value: 0.5
-    max_value: 10
-    step: 0.5
-
-#############################################
-# General Sensors 
-# https://esphome.io/components/sensor/index.html
-#############################################
-sensor:
-  - platform: bme280_i2c
-    temperature:
-      name: ${friendly_name} BME280 Temp
-      accuracy_decimals: 1     
-      oversampling: 2x
-    pressure:
-      name: ${friendly_name} BME280 Pressure
-      oversampling: 2x
-    humidity:
-      name: ${friendly_name} BME280 Humidity
-      accuracy_decimals: 1     
-      oversampling: 2x
-    address: 0x76
-    update_interval: ${update_time}   
-  - platform: uptime
-    name: ${friendly_name} Uptime
-  - platform: template
-    name: ${friendly_name} LD1125H Distance
-    id: LD1125H_Distance
-    icon: "mdi:signal-distance-variant"
-    unit_of_measurement: "m"
-    accuracy_decimals: 2
-    filters:    # Use Fliter To Debounce
-    - sliding_window_moving_average:
-        window_size: 8
-        send_every: 2
-    - heartbeat: 0.2s
-
-#############################################
-# Text Sensors (custom component)
-# refer https://github.com/ssieb/esphome_components/tree/master/components/serial
-#############################################
-text_sensor:
-  - platform: serial
-    uart_id: LD1125H_UART_BUS
-    name: ${friendly_name} LD1125H UART Text
-    id: LD1125H_UART_Text
-    icon: "mdi:format-text"
-    internal: True #If Don't Want to See UART Receive Data, Set To True
-    on_value:
-      lambda: |-
-        if (id(LD1125H_UART_Text).state.substr(0,3) == "occ") {
-          id(LD1125H_Distance).publish_state(atof(id(LD1125H_UART_Text).state.substr(9).c_str()));
-          if ((time(NULL)-id(LD1125H_Last_Mov_Time))>id(LD1125H_Mov_Time).state) {
-            id(LD1125H_Occupancy).publish_state("Occupancy");
-            if (id(LD1125H_MovOcc_Binary).state == false) {
-              id(LD1125H_MovOcc_Binary).publish_state(true);
-            }
-            if (id(LD1125H_Mov_Binary).state == true) {
-              id(LD1125H_Mov_Binary).publish_state(false);
-            }
-          }
-          if (id(LD1125H_MovOcc_Binary).state == false) {
-            id(LD1125H_MovOcc_Binary).publish_state(true);
-          }
-          id(LD1125H_Last_Time) = time(NULL);
-          if (id(LD1125H_Clearence_Status) == true) {
-            id(LD1125H_Clearence_Status) = false;
-          }
-        }
-        else if (id(LD1125H_UART_Text).state.substr(0,3) == "mov") {
-          id(LD1125H_Distance).publish_state(atof(id(LD1125H_UART_Text).state.substr(9).c_str()));
-          id(LD1125H_Occupancy).publish_state("Movement");
-          if (id(LD1125H_MovOcc_Binary).state == false) {
-            id(LD1125H_MovOcc_Binary).publish_state(true);
-          }
-          if (id(LD1125H_Mov_Binary).state == false) {
-            id(LD1125H_Mov_Binary).publish_state(true);
-          }
-          id(LD1125H_Last_Mov_Time) = time(NULL);
-          id(LD1125H_Last_Time) = time(NULL);
-          if (id(LD1125H_Clearence_Status) == true) {
-            id(LD1125H_Clearence_Status) = false;
-          }
-        }
-  - platform: template
-    name: ${friendly_name} LD1125H Occupancy Status
-    id: LD1125H_Occupancy
-    icon: "mdi:motion-sensor"
-
-#############################################
-# Binary Sensors
-# https://esphome.io/components/binary_sensor/index.html
-#############################################
-binary_sensor:
-  - platform: status
-    name: ${friendly_name} Status
-  - platform: template
-    name: ${friendly_name} LD1125H Occupancy or Movement
-    id: LD1125H_MovOcc_Binary
-    device_class: occupancy
-  - platform: template
-    name: ${friendly_name} LD1125H Movement
-    id: LD1125H_Mov_Binary
-    device_class: motion  

esphome/trash/esp-occupancystair copy.yaml

@@ -1,404 +0,0 @@
-#############################################
-#############################################
-# HiLink LD2410 mmWave sensor, with BME280 Temp/Hum/Pres Sensor on an ESP32
-# https://github.com/patrick3399/Hi-Link_mmWave_Radar_ESPHome/tree/main
-# https://github.com/patrick3399/Hi-Link_mmWave_Radar_ESPHome/blob/main/LD1125H/ESP32-LD1125H-Complete.yaml
-#
-# https://esphome.io/components/sensor/ld2410.html
-# https://www.simplysmart.house/blog/presence-detection-ld2410-home-assistant
-# 
-#############################################
-#############################################
-
-#############################################
-# Variable Substitutions
-#############################################
-substitutions:
-  devicename: "esp-occupancystair"
-  friendly_name: "Stair Occupancy"
-  description_comment: "D1 Mini ESP32 with LD2410 mmWave for internal stairwell and environment sensors for under house"
-  api_key: !secret esp-occupancystair_api_key #unfortunately you can't use substitutions in secrets names
-  ota_pass: !secret esp-occupancystair_ota_pass #unfortunately you can't use substitutions in secrets names
-  mqtt_topic: "esphome" #main topic for the mqtt server, call it what you like
-  update_time: 30s #update time for for temp sensors etc
-
-#############################################
-# ESPHome
-# https://esphome.io/components/esphome.html
-#############################################
-esphome:
-  name: ${devicename}
-  comment: ${description_comment} #appears on the esphome page in HA
-  #on_boot:    #Initial Setting, will remember previous values (if set)
-    #priority: -200
-    #then:
-
-
-#############################################
-# ESP Platform and Framework
-# https://esphome.io/components/esp32.html
-#############################################
-esp32:
-  board: esp32dev
-  framework:
-    #type: arduino
-    type: esp-idf  #Suggested Use ESP-IDF Framework, or Plug Out the UART Cable Might Cause ESP32 Hang. 
-    version: recommended #recommended, latest or dev
-
-#############################################
-# i2s bus
-# https://esphome.io/components/i2c.html
-#############################################
-i2c:
-  sda: GPIO19
-  scl: GPIO21
-  scan: True  
-  frequency: 100kHz #10, 50, 100, 200, 800 are possible settings, 100kHz was reliable for me
-
-#############################################    
-# ESPHome Logging Enable
-# https://esphome.io/components/logger.html
-############################################# 
-logger:
-  level: INFO  #INFO Level suggested, or DEBUG for testing
-  baud_rate: 0 #set to 0 for no logging via UART, needed if you are using it for other serial things (eg PZEM)
-  #esp8266_store_log_strings_in_flash: false
-  #tx_buffer_size: 64
-
-#############################################    
-# Enable the Home Assistant API
-# https://esphome.io/components/api.html
-#############################################  
-api:
-  encryption:
-    key: ${api_key}
-
-#############################################    
-# Enable Over the Air Update Capability
-# https://esphome.io/components/ota.html?highlight=ota
-#############################################  
-ota:
-  safe_mode: true  #Safe mode will detect boot loops
-  password: ${ota_pass}
-
-#############################################    
-# Wifi Settings 
-# https://esphome.io/components/wifi.html
-#############################################  
-wifi:
-  ssid: !secret wifi_ssid
-  password: !secret wifi_password
-  #power_save_mode: LIGHT #https://esphome.io/components/wifi.html#wifi-power-save-mode
-  #manual_ip: #optional static IP address
-    #static_ip: 192.168.x.x
-    #gateway: 192.168.X.x
-    #subnet: 255.255.255.0
-  ap:   #Details for fallback hotspot (captive portal) in case wifi connection fails https://esphome.io/components/wifi.html#access-point-mode
-    ssid: $devicename fallback AP
-    password: !secret fallback_ap_password
-    ap_timeout: 5min #default is 1min
-
-#############################################    
-# Web Portal for display and monitoring
-# Turning this off is probably a good idea to save resources.
-# https://esphome.io/components/web_server.html
-#############################################   
-web_server:
-  port: 80
-#   username: !secret web_server_username #probably a good idea to secure it
-#    password: !secret web_server_password
-
-#############################################
-# MQTT Monitoring
-# https://esphome.io/components/mqtt.html?highlight=mqtt
-# MUST also have api enabled if you enable MQTT
-#############################################
-mqtt:
-  broker: !secret mqtt_server
-  topic_prefix: ${mqtt_topic}/${devicename}
-  username: !secret mqtt_username
-  password: !secret mqtt_password
-
-#############################################    
-# Bluetooth
-# https://esphome.io/components/bluetooth_proxy.html
-# https://esphome.io/components/esp32_ble_tracker.html
-# Remember that this takes a LOT of processing. On the 
-# ESP32, enable the  IDF framework, and disable the 
-# Web server component.  Changing to the IDF framework 
-# needs to be via cable not OTA to change the
-# partition setup.
-#############################################  
-#bluetooth_proxy:
-
-#esp32_ble_tracker:
-
-#############################################
-# UART Serial
-# hardware on EPS32, but software, and can be glitchy on ESP8266
-# https://esphome.io/components/uart.html?highlight=uart
-#############################################
-uart:
-  id: ld2410_uart
-  rx_pin: GPIO16  #For ESP32, you can use any pin, Recommend Use UART_2, Don't use UART_0, It might Cause Boot Fail or System Hang
-  tx_pin: GPIO17  #For ESP32, you can use any pin, Recommend Use UART_2, Don't use UART_0, It might Cause Boot Fail or System Hang
-#  rx_pin: GPIO1  #For ESP32, you can use any pin, Recommend Use UART_2, Don't use UART_0, It might Cause Boot Fail or System Hang
-#  tx_pin: GPIO0 #For ESP32, you can use any pin, Recommend Use UART_2, Don't use UART_0, It might Cause Boot Fail or System Hang
-  baud_rate: 256000 # default for LD2410 is 25600, 8, 0, NONE
-  data_bits: 8
-  stop_bits: 1
-  parity: NONE
-#  debug:
-#    direction: BOTH
-#    dummy_receiver: false
-#    after:
-#      delimiter: "\n"
-#    sequence:
-#      - lambda: UARTDebug::log_string(direction, bytes);
-
-#############################################
-# General esp status LED
-# https://esphome.io/components/status_led.html
-#############################################
-status_led:
-  pin:
-    number: GPIO2 #ESP32 Onboard LED
-    ignore_strapping_warning: True #https://esphome.io/guides/faq.html#why-am-i-getting-a-warning-about-strapping-pins
-    inverted: false
-
-
-#############################################
-# LD2410 Sensors
-# https://esphome.io/components/sensor/ld2410.html
-# https://www.hlktech.net/index.php?id=988
-#############################################
-ld2410:
-  uart_id: ld2410_uart
-  #uart_id (Optional, ID): Manually specify the ID of the UART Component if you want to use multiple UART buses.
-  #throttle (Optional, int): Time in milliseconds to control the rate of data updates. Defaults to 1000ms.
-  #id (Optional, ID): Manually specify the ID for this LD2410 Sensor component if you need multiple components.
-
-# light (Optional, int): When in engineering mode, indicates the light sensitivity, otherwise unknown. Value between 0 and 255 inclusive. Though it seems that the value 85 is the lowest value at complete darkness. All options from Sensor.
-# moving_distance (Optional, int): Distance in cm of detected moving target. All options from Sensor.
-# still_distance (Optional, int): Distance in cm of detected still target. All options from Sensor.
-# moving_energy (Optional, int): Energy for moving target. Value between 0 and 100 inclusive. All options from Sensor.
-# still_energy (Optional, int): Energy for still target. Value between 0 and 100 inclusive. All options from Sensor.
-# detection_distance (Optional, int): Distance in cm of target. All options from Sensor.
-# gX (Optional): Energies for the Xth gate (X => 0 to 8).
-  # move_energy (Optional, int): When in engineering mode, the move energy of the gate, otherwise unknown. Value between 0 and 100 inclusive. All options from Sensor.
-  #still_energy (Optional, int): When in engineering mode, the still energy of the gate, otherwise unknown. Value between 0 and 100 inclusive. All options from Sensor.
-#ld2410_id (Optional, ID): Manually specify the ID for the LD2410 Sensor component if you are using multiple components.
-
-#The ld2410 number values for setting thresholds
-#  timeout: 5s
-#  max_move_distance: 2.25m
-#  max_still_distance: 2.25m
-#  g0_move_threshold: 40  # 0m / 0'
-#  g0_still_threshold: 10 # 0m / 0'
-#  g1_move_threshold: 40  # 0 - 0.75m / 0 - 2.46'
-#  g1_still_threshold: 10 # 0 - 0.75m / 0 - 2.46'
-#  g2_move_threshold: 40  # 0.75 - 1.5m / 2.46' - 4.92'
-#  g2_still_threshold: 10 # 0.75 - 1.5m / 2.46' - 4.92'
-#  g3_move_threshold: 40  # 1.5 - 2.25m / 4.92' - 7.38'
-#  g3_still_threshold: 10 # 1.5 - 2.25m / 4.92' - 7.38'
-#  g4_move_threshold: 40  # 2.25 - 3m' / 7.38' - 9.84'
-#  g4_still_threshold: 40 # 2.25 - 3m' / 7.38' - 9.84'
-#  g5_move_threshold: 40  # 3 - 3.75 / 9.84' - 12.30'
-#  g5_still_threshold: 40 # 3 - 3.75 / 9.84' - 12.30'
-#  g6_move_threshold: 30  # 3.75 - 4.5m / 12.30' - 14.76'
-#  g6_still_threshold: 15 # 3.75 - 4.5m / 12.30' - 14.76'
-#  g7_move_threshold: 30  # 4.5 - 5.25m / 14.76' - 17.22'
-#  g7_still_threshold: 15 # 4.5 - 5.25m / 14.76' - 17.22'
-#  g8_move_threshold: 30  # 5.25 - 6m / 17.22' - 19.68'
-#  g8_still_threshold: 15 # 5.25 - 6m / 17.22' - 19.68'
-number:
-  - platform: ld2410
-    timeout:
-      name: Timeout
-    light_threshold:
-      name: Light Threshold
-    max_move_distance_gate:
-      name: Max Move Distance Gate
-    max_still_distance_gate:
-      name: Max Still Distance Gate
-    g0:
-      move_threshold:
-        name: g0 move threshold
-      still_threshold:
-        name: g0 still threshold
-    g1:
-      move_threshold:
-        name: g1 move threshold
-      still_threshold:
-        name: g1 still threshold
-    g2:
-      move_threshold:
-        name: g2 move threshold
-      still_threshold:
-        name: g2 still threshold
-    g3:
-      move_threshold:
-        name: g3 move threshold
-      still_threshold:
-        name: g3 still threshold
-    g4:
-      move_threshold:
-        name: g4 move threshold
-      still_threshold:
-        name: g4 still threshold
-    g5:
-      move_threshold:
-        name: g5 move threshold
-      still_threshold:
-        name: g5 still threshold
-    g6:
-      move_threshold:
-        name: g6 move threshold
-      still_threshold:
-        name: g6 still threshold
-    g7:
-      move_threshold:
-        name: g7 move threshold
-      still_threshold:
-        name: g7 still threshold
-    g8:
-      move_threshold:
-        name: g8 move threshold
-      still_threshold:
-        name: g8 still threshold
-
-#The ld2410 select allows you to control your LD2410 Sensor.
-#distance_resolution (Optional): Control the gates distance resolution. Can be 0.75m or 0.2m. Defaults to 0.75m. All options from Select.
-#baud_rate (Optional): Control the serial port baud rate. Defaults to 256000. Once changed, all sensors will stop working until a fresh install with an updated UART Component configuration. All options from Select.
-#light_function (Optional): If set, will affect the OUT pin value, based on light threshold. Can be off, low or above. Defaults to off. All options from Select.
-#out_pin_level (Optional): Control OUT pin away value. Can be low or high. Defaults to low. All options from Select.
-#ld2410_id (Optional, ID): Manually specify the ID for the LD2410 Sensor component if you are using multiple components.
-select:
-  - platform: ld2410
-    distance_resolution: 
-      name: "distance resolution"
-    baud_rate:
-      name: "baud rate"
-    light_function:
-      name: light function
-    out_pin_level:
-      name: out pin level
-
-#############################################
-# General Sensors 
-# https://esphome.io/components/sensor/index.html
-#############################################
-sensor:
-  - platform: bme280_i2c
-    temperature:
-      name: ${friendly_name} BME280 Temp
-      accuracy_decimals: 1     
-      oversampling: 2x
-    pressure:
-      name: ${friendly_name} BME280 Pressure
-      oversampling: 2x
-    humidity:
-      name: ${friendly_name} BME280 Humidity
-      accuracy_decimals: 1     
-      oversampling: 2x
-    address: 0x76
-    update_interval: ${update_time}   
-  - platform: uptime
-    name: ${friendly_name} Uptime
-#The ld2410 sensor values
-  - platform: ld2410
-    light:
-      name: Light
-    moving_distance:
-      name : Moving Distance
-    still_distance:
-      name: Still Distance
-    moving_energy:
-      name: Move Energy
-    still_energy:
-      name: Still Energy
-    detection_distance:
-      name: Detection Distance
-    g0:
-      move_energy:
-        name: g0 move energy
-      still_energy:
-        name: g0 still energy
-    g1:
-      move_energy:
-        name: g1 move energy
-      still_energy:
-        name: g1 still energy
-    g2:
-      move_energy:
-        name: g2 move energy
-      still_energy:
-        name: g2 still energy
-    g3:
-      move_energy:
-        name: g3 move energy
-      still_energy:
-        name: g3 still energy
-    g4:
-      move_energy:
-        name: g4 move energy
-      still_energy:
-        name: g4 still energy
-    g5:
-      move_energy:
-        name: g5 move energy
-      still_energy:
-        name: g5 still energy
-    g6:
-      move_energy:
-        name: g6 move energy
-      still_energy:
-        name: g6 still energy
-    g7:
-      move_energy:
-        name: g7 move energy
-      still_energy:
-        name: g7 still energy
-    g8:
-      move_energy:
-        name: g8 move energy
-      still_energy:
-        name: g8 still energy
-
-# The ld2410 switch allows you to control your LD2410 Sensor.
-switch:
-  - platform: ld2410
-    engineering_mode:
-      name: "Engineering Mode"
-    bluetooth:
-      name: "Control Bluetooth"
-
-#The ld2410 binary sensors to get presence notification
-binary_sensor:
-  - platform: ld2410
-    has_target:
-      name: Presence
-    has_moving_target:
-      name: Moving Target
-    has_still_target:
-      name: Still Target
-    out_pin_presence_status:
-      name: Out Pin Presence Status
-
-#The ld2410 button allows resetting
-button:
-  - platform: ld2410
-    factory_reset:
-      name: "Factory reset"
-    restart:
-      name: "Restart"
-    query_params:
-      name: Query Parameters
-
-#The ld2410 text sensor allows you to get information about your LD2410 Sensor.
-text_sensor:
-  - platform: ld2410
-    version:
-      name: "Firmware Version"
-    mac_address:
-      name: "MAC Address"

esphome/trash/esp-occupancystairs.yaml

@@ -1,31 +0,0 @@
-esphome:
-  name: esp-occupancystairs
-  friendly_name: esp-occupancystairs
-
-esp32:
-  board: esp32dev
-  framework:
-    type: arduino
-
-# Enable logging
-logger:
-
-# Enable Home Assistant API
-api:
-  encryption:
-    key: "SjiVZdG8rekBlk9bEZIE8+cIhvs6Dodj9GuFLFpJypk="
-
-ota:
-  password: "2b76bfe3274afc8b17020059fec18c96"
-
-wifi:
-  ssid: !secret wifi_ssid
-  password: !secret wifi_password
-
-  # Enable fallback hotspot (captive portal) in case wifi connection fails
-  ap:
-    ssid: "Esp-Occupancystairs"
-    password: "zfhq7q6HYG2J"
-
-captive_portal:
-    

esphome/trash/esphome-web-7776ec.yaml

@@ -1,393 +0,0 @@
-#############################################
-# Variable Substitutions
-#############################################
-substitutions:
-  devicename: "esphome-web-7776ec"
-  friendly_name: "esp-web-7776ec"
-  upper_devicename: "esp-web-7776ec"
-  mqtt_topic: "esphome"
-  update_time: 30s #for temp sensors etc
-
-#############################################
-# ESPHome
-# https://esphome.io/components/esphome.html#esphome-core-configuration
-#############################################
-esphome:
-  name: ${devicename}
-  comment: D1 Mini ESP32 with mmWave and environment sensors for main office #appears on the esphome page in HA
-  on_boot:    #LD1125H Initial Setting
-    priority: -200
-    then:
-      - uart.write:
-          id: LD1125H_UART_BUS
-          data: !lambda |-
-            std::string th1st = "mth1=" + str_sprintf("%.0f",id(LD1125H_mth1).state) +"\r\n";
-            return std::vector<uint8_t>(th1st.begin(), th1st.end());
-      - uart.write:
-          id: LD1125H_UART_BUS
-          data: !lambda |-
-            std::string th2st = "mth2=" + str_sprintf("%.0f",id(LD1125H_mth2).state) +"\r\n";
-            return std::vector<uint8_t>(th2st.begin(), th2st.end());
-      - uart.write:
-          id: LD1125H_UART_BUS
-          data: !lambda |-
-            std::string th3st = "mth3=" + str_sprintf("%.0f",id(LD1125H_mth3).state) +"\r\n";
-            return std::vector<uint8_t>(th3st.begin(), th3st.end());
-      - uart.write:
-          id: LD1125H_UART_BUS
-          data: !lambda |-
-            std::string rmaxst = "rmax=" + str_sprintf("%.1f",id(LD1125H_rmax).state) +"\r\n";
-            return std::vector<uint8_t>(rmaxst.begin(), rmaxst.end());
-
-#############################################
-# ESP Platform and Framework
-# https://esphome.io/components/esp32.html
-#############################################
-esp32:
-  board: nodemcu-32s
-  framework:
-    type: arduino
-    #type: esp-idf  #Suggested Use ESP-IDF Framework, or Plug Out the UART Cable Might Cause ESP32 Hang. 
-    version: recommended #recommended, latest or dev
-
-#############################################
-# i2s bus
-# https://esphome.io/components/i2c.html
-#############################################
-i2c:
-  sda: GPIO19
-  scl: GPIO21
-  scan: True  
-  frequency: 100kHz #10, 50, 100, 200, 800 are possible settings, 100kHz was reliable for me
-
-
-#############################################    
-# ESPHome external or custom components to use
-############################################# 
-external_components:
-  - source:
-      type: git
-      url: https://github.com/ssieb/custom_components #Thanks for @ssieb components.
-    components: [ serial ]  #text_sensor that reads lines for a uart. Also, a sensor that reads single values from the uart.
-
-#############################################    
-# ESPHome Logging Enable
-############################################# 
-logger:
-  level: INFO  #INFO Level suggested, or DEBUG for testing
-  baud_rate: 0 #set to 0 for no logging via UART, needed if you are using it for other serial things (eg PZEM)
-  #esp8266_store_log_strings_in_flash: false
-  #tx_buffer_size: 64
-
-#############################################    
-# Enable the Home Assistant API
-#############################################  
-api:
-  #encryption:
-  #key: !secret esp-?_api_key
-
-#############################################    
-# Enable Over the Air Update Capability
-# Safe mode will detect boot loops
-#############################################  
-ota:
-  safe_mode: true
-  password: !secret esp-mmwaveoffice_ota_pass
-
-#############################################    
-# Wifi Settings 
-#############################################  
-wifi:
-  ssid: !secret wifi_ssid
-  password: !secret wifi_password
-  #power_save_mode: LIGHT #https://esphome.io/components/wifi.html#wifi-power-save-mode
-  #manual_ip:
-    #static_ip: 192.168.x.x
-    #gateway: 192.168.X.x
-    #subnet: 255.255.255.0
-  #ap:   #Details for fallback hotspot (captive portal) in case wifi connection fails
-    #ssid: "? Fallback Hotspot"
-    #password: !secret fallback_ap_password
-
-#############################################    
-# Web Portal for display and monitoring
-# Turning this off is probably a good idea to save resources.
-#############################################   
-web_server:
-  port: 80
-#   username: !secret web_server_username
-#    password: !secret web_server_password
-
-#############################################
-# MQTT Monitoring
-#############################################
-mqtt:
-  broker: !secret mqtt_server
-  topic_prefix: ${mqtt_topic}/${devicename}
-  username: !secret mqtt_username
-  password: !secret mqtt_password
-
-#############################################  
-#############################################
-# MAIN SENSORS
-#############################################
-#############################################
-uart:
-  id: LD1125H_UART_BUS
-  rx_pin: GPIO16  #For ESP32, you can use any pin, Recommend Use UART_2, Don't use UART_0, It might Cause Boot Fail or System Hang
-  tx_pin: GPIO17  #For ESP32, you can use any pin, Recommend Use UART_2, Don't use UART_0, It might Cause Boot Fail or System Hang
-#  rx_pin: GPIO1  #For ESP32, you can use any pin, Recommend Use UART_2, Don't use UART_0, It might Cause Boot Fail or System Hang
-#  tx_pin: GPIO0 #For ESP32, you can use any pin, Recommend Use UART_2, Don't use UART_0, It might Cause Boot Fail or System Hang
-  baud_rate: 115200
-  data_bits: 8
-  stop_bits: 1
-  parity: NONE
-#  debug:
-#    direction: BOTH
-#    dummy_receiver: false
-#    after:
-#      delimiter: "\n"
-#    sequence:
-#      - lambda: UARTDebug::log_string(direction, bytes);
-
-#############################################
-# Global Variables for use in templates etc
-#############################################
-globals:
-  - id: LD1125H_Last_Time
-    type: time_t
-    restore_value: no
-    initial_value: time(NULL)
-  - id: LD1125H_Last_Mov_Time
-    type: time_t
-    restore_value: no
-    initial_value: time(NULL)
-  - id: LD1125H_Clearence_Status
-    type: bool
-    restore_value: no
-    initial_value: "false"
-
-#############################################
-# General esp status LED
-#############################################
-status_led:
-  pin:
-    number: GPIO2 #ESP32 OnBroad LED
-    inverted: false
-
-#############################################
-# Interval Automations 
-# https://esphome.io/guides/automations.html#interval-component         
-#############################################
-interval:
-  - interval: 1s #Clearance Scan Time
-    setup_priority: -200
-    then:
-      lambda: |-
-        if ((time(NULL)-id(LD1125H_Last_Time))>id(LD1125H_Clear_Time).state) {
-          if ((id(LD1125H_Clearence_Status) == false) || (id(LD1125H_Occupancy).state != "Clearance")) {
-            id(LD1125H_Occupancy).publish_state("Clearance");
-            id(LD1125H_Clearence_Status) = true;
-          }
-          if (id(LD1125H_MovOcc_Binary).state == true) {
-            id(LD1125H_MovOcc_Binary).publish_state(false);
-          }
-          if (id(LD1125H_Mov_Binary).state == true) {
-            id(LD1125H_Mov_Binary).publish_state(false);
-          }
-        }
-
-#############################################
-# Number Sensors (custom component)        
-# refer https://github.com/ssieb/esphome_components/tree/master/components/serial
-#############################################
-number:
-  - platform: template
-    name: ${upper_devicename} LD1125H mth1 #mth1 is 0~2.8m Sensitivity.
-    id: LD1125H_mth1
-    icon: "mdi:cogs"
-    optimistic: true
-    restore_value: true #If you don't want to store the setting at ESP, set it to false.
-    initial_value: "60.0" #Default mth1 Setting
-    min_value: 10.0
-    max_value: 600.0
-    step: 5.0
-    set_action:
-      then:
-        - uart.write:
-            id: LD1125H_UART_BUS
-            data: !lambda |-
-              std::string th1st = "mth1=" + str_sprintf("%.0f",x) +"\r\n";
-              return std::vector<uint8_t>(th1st.begin(), th1st.end());
-  - platform: template
-    name: ${upper_devicename} LD1125H mth2 #mth2 is 2.8~8m Sensitivity.
-    id: LD1125H_mth2
-    icon: "mdi:cogs"
-    optimistic: true
-    restore_value: true #If you don't want to store the setting at ESP, set it to false.
-    initial_value: "30" #Default mth2 Setting
-    min_value: 5
-    max_value: 300
-    step: 5
-    set_action:
-      then:
-        - uart.write:
-            id: LD1125H_UART_BUS
-            data: !lambda |-
-              std::string th2st = "mth2=" + str_sprintf("%.0f",x) +"\r\n";
-              return std::vector<uint8_t>(th2st.begin(), th2st.end());
-  - platform: template
-    name: ${upper_devicename} LD1125H mth3 #mth3 is above 8m Sensitivity.
-    id: LD1125H_mth3
-    icon: "mdi:cogs"
-    optimistic: true
-    restore_value: true #If you don't want to store the setting at ESP, set it to false.
-    initial_value: "20" #Default mth3 Setting
-    min_value: 5
-    max_value: 200
-    step: 5
-    set_action:
-      then:
-        - uart.write:
-            id: LD1125H_UART_BUS
-            data: !lambda |-
-              std::string th3st = "mth3=" + str_sprintf("%.0f",x) +"\r\n";
-              return std::vector<uint8_t>(th3st.begin(), th3st.end());
-  - platform: template
-    name: ${upper_devicename} LD1125H rmax #rmax is max detection distance.
-    id: LD1125H_rmax
-    icon: "mdi:cogs"
-    optimistic: true
-    restore_value: true #If you don't want to store the setting at ESP, set it to false.
-    initial_value: "8" #Default rmax Setting
-    min_value: 0.4
-    max_value: 12
-    step: 0.1
-    set_action:
-      then:
-        - uart.write:
-            id: LD1125H_UART_BUS
-            data: !lambda |-
-              std::string rmaxst = "rmax=" + str_sprintf("%.1f",x) +"\r\n";
-              return std::vector<uint8_t>(rmaxst.begin(), rmaxst.end());
-  - platform: template
-    name: ${upper_devicename} LD1125H Clearence Time
-    id: LD1125H_Clear_Time
-    icon: "mdi:cogs"
-    optimistic: true
-    restore_value: true #If you don't want to store the setting at ESP, set it to false.
-    initial_value: "5" #LD1125H Mov/Occ > Clearence Time Here
-    min_value: 0.5
-    max_value: 20
-    step: 0.5
-  - platform: template
-    name: ${upper_devicename} LD1125H Movement Time
-    id: LD1125H_Mov_Time
-    icon: "mdi:cogs"
-    optimistic: true
-    restore_value: true #If you don't want to store the setting at ESP, set it to false.
-    initial_value: "1" #LD1125H Mov > Occ Time Here
-    min_value: 0.5
-    max_value: 10
-    step: 0.5
-
-#############################################
-# General Sensors 
-# https://esphome.io/components/sensor/index.html
-#############################################
-sensor:
-  - platform: bme280_i2c
-    temperature:
-      name: ${upper_devicename} BME280 Temp
-      accuracy_decimals: 1     
-      oversampling: 2x
-    pressure:
-      name: ${upper_devicename} BME280 Pressure
-      oversampling: 2x
-    humidity:
-      name: ${upper_devicename} BME280 Humidity
-      accuracy_decimals: 1     
-      oversampling: 2x
-    address: 0x76
-    update_interval: ${update_time}   
-  - platform: uptime
-    name: ${upper_devicename} Uptime
-  - platform: template
-    name: ${upper_devicename} LD1125H Distance
-    id: LD1125H_Distance
-    icon: "mdi:signal-distance-variant"
-    unit_of_measurement: "m"
-    accuracy_decimals: 2
-    filters:    # Use Fliter To Debounce
-    - sliding_window_moving_average:
-        window_size: 8
-        send_every: 2
-    - heartbeat: 0.2s
-
-#############################################
-# Text Sensors (custom component)
-# refer https://github.com/ssieb/esphome_components/tree/master/components/serial
-#############################################
-text_sensor:
-  - platform: serial
-    uart_id: LD1125H_UART_BUS
-    name: ${upper_devicename} LD1125H UART Text
-    id: LD1125H_UART_Text
-    icon: "mdi:format-text"
-    internal: True #If Don't Want to See UART Receive Data, Set To True
-    on_value:
-      lambda: |-
-        if (id(LD1125H_UART_Text).state.substr(0,3) == "occ") {
-          id(LD1125H_Distance).publish_state(atof(id(LD1125H_UART_Text).state.substr(9).c_str()));
-          if ((time(NULL)-id(LD1125H_Last_Mov_Time))>id(LD1125H_Mov_Time).state) {
-            id(LD1125H_Occupancy).publish_state("Occupancy");
-            if (id(LD1125H_MovOcc_Binary).state == false) {
-              id(LD1125H_MovOcc_Binary).publish_state(true);
-            }
-            if (id(LD1125H_Mov_Binary).state == true) {
-              id(LD1125H_Mov_Binary).publish_state(false);
-            }
-          }
-          if (id(LD1125H_MovOcc_Binary).state == false) {
-            id(LD1125H_MovOcc_Binary).publish_state(true);
-          }
-          id(LD1125H_Last_Time) = time(NULL);
-          if (id(LD1125H_Clearence_Status) == true) {
-            id(LD1125H_Clearence_Status) = false;
-          }
-        }
-        else if (id(LD1125H_UART_Text).state.substr(0,3) == "mov") {
-          id(LD1125H_Distance).publish_state(atof(id(LD1125H_UART_Text).state.substr(9).c_str()));
-          id(LD1125H_Occupancy).publish_state("Movement");
-          if (id(LD1125H_MovOcc_Binary).state == false) {
-            id(LD1125H_MovOcc_Binary).publish_state(true);
-          }
-          if (id(LD1125H_Mov_Binary).state == false) {
-            id(LD1125H_Mov_Binary).publish_state(true);
-          }
-          id(LD1125H_Last_Mov_Time) = time(NULL);
-          id(LD1125H_Last_Time) = time(NULL);
-          if (id(LD1125H_Clearence_Status) == true) {
-            id(LD1125H_Clearence_Status) = false;
-          }
-        }
-  - platform: template
-    name: ${upper_devicename} LD1125H Occupancy Status
-    id: LD1125H_Occupancy
-    icon: "mdi:motion-sensor"
-
-#############################################
-# Binary Sensors
-# https://esphome.io/components/binary_sensor/index.html
-#############################################
-binary_sensor:
-  - platform: status
-    name: ${upper_devicename} Status
-  - platform: template
-    name: ${upper_devicename} LD1125H Occupancy or Movement
-    id: LD1125H_MovOcc_Binary
-    device_class: occupancy
-  - platform: template
-    name: ${upper_devicename} LD1125H Movement
-    id: LD1125H_Mov_Binary
-    device_class: motion