Edit esp-gasheater.yaml

esphome/esp-gasheater.yaml

@@ -432,33 +432,37 @@ binary_sensor:
           if (!id(test_mode_enabled).state && id(mode_select).state == "AUTO") {
             id(warmup_until_ms) = millis() + (${warmup_seconds} * 1000UL);
           }
-      - choose:
+      # ESPHome does not support Home Assistant's `choose:` action here,
-          # OFF mode watches for local physical heater starts.
+      # so this is written as nested if/else logic.
-          # If someone presses the real heater ON button, the LEDs come on, this
+      - if:
-          # powered_state turns ON, and ESPHome changes to AUTO and takes over.
+          condition:
-          - conditions:
+            # OFF mode watches for local physical heater starts.
-              - lambda: 'return !id(test_mode_enabled).state && id(mode_select).state == "OFF" && !id(self_power_on);'
+            # If someone presses the real heater ON button, the LEDs come on, this
-            sequence:
+            # powered_state turns ON, and ESPHome changes to AUTO and takes over.
-              - script.execute: local_on_takeover
+            lambda: 'return !id(test_mode_enabled).state && id(mode_select).state == "OFF" && !id(self_power_on);'
-
+          then:
-          # In AUTO/MANUAL, if the controller intended the heater OFF but LEDs say ON,
+            - script.execute: local_on_takeover
-          # force the heater OFF. OFF is excluded because OFF performs local-start takeover.
+          else:
-          - conditions:
+            - if:
-              - lambda: 'return !id(test_mode_enabled).state && id(mode_select).state != "BYPASS (Remote Only)" && id(mode_select).state != "OFF" && !id(power_intended_on) && !id(self_power_on);'
+                condition:
-            sequence:
+                  # In AUTO/MANUAL, if the controller intended the heater OFF but LEDs say ON,
-              - script.execute: enforce_heater_off
+                  # force the heater OFF. OFF is excluded because OFF performs local-start takeover.
-
+                  lambda: 'return !id(test_mode_enabled).state && id(mode_select).state != "BYPASS (Remote Only)" && id(mode_select).state != "OFF" && !id(power_intended_on) && !id(self_power_on);'
-          # If the heater turns on externally while AUTO already intended it ON,
+                then:
-          # re-baseline after warmup and continue normal automatic control.
+                  - script.execute: enforce_heater_off
-          - conditions:
+                else:
-              - lambda: 'return !id(test_mode_enabled).state && id(mode_select).state == "AUTO" && id(power_intended_on) && !id(self_power_on);'
+                  - if:
-            sequence:
+                      condition:
-              - lambda: |-
+                        # If the heater turns on externally while AUTO already intended it ON,
-                  id(ramp_until_ms) = millis() + (${fast_ramp_seconds} * 1000UL);
+                        # re-baseline after warmup and continue normal automatic control.
-              - delay: ${warmup_seconds}s
+                        lambda: 'return !id(test_mode_enabled).state && id(mode_select).state == "AUTO" && id(power_intended_on) && !id(self_power_on);'
-              - script.execute: calibrate_to_min
+                      then:
-              - script.execute: auto_control_tick
+                        - lambda: |-
-              - script.execute: adjust_to_desired
+                            id(ramp_until_ms) = millis() + (${fast_ramp_seconds} * 1000UL);
+                        - delay: ${warmup_seconds}s
+                        - script.execute: calibrate_to_min
+                        - script.execute: auto_control_tick
+                        - script.execute: adjust_to_desired
 
     on_release:
       - lambda: |-