esphome mi 1s lamp

esphome/esp-occupancyoffice.yaml

@@ -1,4 +1,3 @@
-
 #############################################
 #############################################
 # HiLink LD1125H mmWave sensor, with BME280 Temp/Hum/Pres Sensor on an ESP32
@@ -24,7 +23,7 @@
 #############################################
 substitutions:
   devicename: "esp-occupancyoffice"
-  friendly_name: "Office State"
+  friendly_name: "Office Occupancy & Environment"
   description_comment: "D1 Mini ESP32 with LD1125H mmWave and environment sensors for downstairs office"
 
   #if NOT using a secrets file, just replace these with the passwords etc (in quotes)
@@ -54,7 +53,9 @@ substitutions:
 #############################################
 esphome:
   name: ${devicename}
+  friendly_name: ${friendly_name}
   comment: ${description_comment} #appears on the esphome page in HA
+  min_version: 2024.6.0
   on_boot:    #LD1125H Initial Setting, will remember previous values (if set)
     priority: -200
     then:
@@ -84,23 +85,12 @@ esphome:
 # https://esphome.io/components/esp32.html
 #############################################
 esp32:
-  #board: nodemcu-32s
   board: esp32dev
   framework:
     #type: arduino
     type: esp-idf  #Suggest using the ESP-IDF Framework. Changing from arduino to esp-idf needs a cabled download to change partitions
     version: recommended #recommended, latest or dev
 
-#############################################
-# i2s bus
-# https://esphome.io/components/i2c.html
-#############################################
-i2c:
-  sda: GPIO19
-  scl: GPIO21
-  scan: True  
-  frequency: 100kHz #10, 50, 100, 200, 800 are possible settings, 100kHz was reliable for me
-
 #############################################    
 # ESPHome external or custom components to use
 # https://esphome.io/components/external_components.html
@@ -129,14 +119,26 @@ logger:
 api:
   encryption:
     key: ${api_key}
+  on_client_connected:
+    - esp32_ble_tracker.start_scan:
+       continuous: true
+  on_client_disconnected:
+    - esp32_ble_tracker.stop_scan:
 
 #############################################    
 # Enable Over the Air Update Capability
 # https://esphome.io/components/ota.html?highlight=ota
 #############################################  
 ota:
-  safe_mode: true  #Safe mode will detect boot loops
-  password: ${ota_pass}
+  - platform: esphome
+    password: ${ota_pass}
+
+#############################################    
+# Safe Mode
+# Safe mode will detect boot loops
+# https://esphome.io/components/safe_mode
+#############################################  
+safe_mode:
 
 #############################################    
 # Wifi Settings 
@@ -155,10 +157,10 @@ wifi:
     #static_ip: ${static_ip_address}
     #gateway: ${static_ip_gateway}
     #subnet: ${static_ip_subnet}
-  ap:   #Details for fallback hotspot (captive portal) in case wifi connection fails https://esphome.io/components/wifi.html#access-point-mode
+  ap:   #Details for fallback hotspot in case wifi connection fails https://esphome.io/components/wifi.html#access-point-mode
     ssid: ${devicename} fallback AP
     password: ${fallback_ap_password}
-    ap_timeout: 5min #default is 1min
+    ap_timeout: 30min #Time until it brings up fallback AP. default is 1min
 
 #############################################    
 # Web Portal for display and monitoring
@@ -182,20 +184,17 @@ mqtt:
   username: ${mqtt_username}
   password: ${mqtt_password}
 
-#############################################    
-# Bluetooth
-# https://esphome.io/components/bluetooth_proxy.html
-# https://esphome.io/components/esp32_ble_tracker.html
-# Remember that this takes a LOT of processing. On the 
-# ESP32, enable the  IDF framework, and disable the 
-# Web server component.  Changing to the IDF framework 
-# needs to be via cable not OTA to change the
-# partition setup.
-#############################################  
-#bluetooth_proxy:
-#  active: true
-
-#esp32_ble_tracker:
+#############################################
+# i2c bus
+# https://esphome.io/components/i2c.html
+# 10, 50, 100, 200, 800 are possible settings
+# for frequency, 50kHz is default
+#############################################
+i2c:
+  sda: GPIO19
+  scl: GPIO21
+  scan: True #look for devices on boot up and report
+  frequency: 50kHz
 
 #############################################
 # UART Serial
@@ -211,6 +210,24 @@ uart:
   stop_bits: 1
   parity: NONE
 
+#############################################    
+# Bluetooth
+# https://esphome.io/components/bluetooth_proxy.html
+# https://esphome.io/components/esp32_ble_tracker.html
+# Remember that this takes a LOT of processing. On the 
+# ESP32, enable the  IDF framework, and disable the 
+# Web server component.  Changing to the IDF framework 
+# needs to be via cable not OTA to change the
+# partition setup.
+#############################################  
+bluetooth_proxy:
+  active: true
+  cache_services: true
+
+esp32_ble_tracker:
+    scan_parameters:
+      continuous: false
+
 #############################################
 # Global Variables for use in automations etc
 # https://esphome.io/guides/automations.html?highlight=globals#global-variables
@@ -374,8 +391,10 @@ sensor:
       oversampling: 2x
     address: 0x76
     update_interval: ${update_time}   
+
   - platform: uptime
     name: ${friendly_name} Uptime
+    
   - platform: template
     name: ${friendly_name} LD1125H Distance
     id: LD1125H_Distance