yaml tidyups and warning removals

.ha_run.lock

@@ -1 +1 @@
-{"pid": 67, "version": 1, "ha_version": "2026.1.2", "start_ts": 1768726150.935691}
+{"pid": 67, "version": 1, "ha_version": "2026.1.3", "start_ts": 1769216420.8243344}

esphome/common/network_common.yaml

@@ -59,12 +59,12 @@ wifi:
   # Allow rapid re-connection to previously connect WiFi SSID, skipping scan of all SSID
   fast_connect: ${wifi_fast_connect}
   # Define dns domain / suffix to add to hostname
-  domain: "${dns_domain}"
+  domain: ${dns_domain}
-  #min_auth_mode: WPA2
+  min_auth_mode: WPA2
   # Reboot eventually when Wi-Fi is down (default is 15min)
   reboot_timeout: 56h
 
-#captive_portal: # extra fallback mechanism for when connecting if the configured WiFi fails
+captive_portal: # extra fallback mechanism for when connecting if the configured WiFi fails
 
 ###########################################################################################
 # Enable Over the Air Update Capability

esphome/common/sntp_common.yaml

@@ -11,6 +11,33 @@ substitutions:
   sntp_server_2: !secret ntp_server_2
   sntp_server_3: !secret ntp_server_3
 
+###########################################################################################
+# Internal clock fallback support
+# If SNTP is invalid, we fall back to a simple internal minute counter
+# We assume user powers on the device at 12:00 noon
+# => 12 * 60 = 720 minutes from midnight.
+# Not restored, so it resets each boot.
+# Therefore, if no network and you still need timing functions, switch on ay noon.
+###########################################################################################
+globals:
+  - id: current_mins
+    type: int
+    restore_value: no
+    initial_value: "720" # 720 is 12:00 Noon
+
+interval:
+  - interval: 60s
+    then:
+      - lambda: |-
+          // If SNTP valid, store minutes since midnight.
+          auto now = id(sntp_time).now();
+          if (now.is_valid()) {
+            id(current_mins) = (now.hour * 60) + now.minute;
+          } else {
+            // Fallback: minutes since boot.
+            id(current_mins) = (int)(millis() / 60000UL);
+          }
+
 ###########################################################################################
 # Real time clock time source for ESPHome
 # If it's invalid, we fall back to an internal clock
@@ -72,7 +99,6 @@ text_sensor:
       }
 
       // Fallback: show internal clock based on current_mins (minutes from midnight).
-      // NOTE: current_mins is expected to be a global defined in the main device YAML.
       int mins = id(current_mins);
       if (mins < 0) mins = 0;
       if (mins >= 1440) mins = mins % 1440;

esphome/esp-6buttontest-pmb.yaml

@@ -360,6 +360,7 @@ status_led:
   pin:
     number: GPIO2
     inverted: yes
+    ignore_strapping_warning: true # GPIO2: This just supresses a warning, we know what we are doing
 
 ##########################################################################################
 # SCRIPT COMPONENT
@@ -478,6 +479,7 @@ binary_sensor:
       number: GPIO05
       mode: INPUT
       inverted: true
+      ignore_strapping_warning: true # GPIO05: This just supresses a warning, we know what we are doing
     name: "Button 3: ${switch_3_name}"
     filters:
       - delayed_on: 50ms
@@ -864,7 +866,7 @@ sensor:
     pin: GPIO36
     id: dimmer_raw
     name: "${variable_1_name} Raw"
-    attenuation: 11db
+    attenuation: 12db
     update_interval: 0.5s
     on_value:
       then:

esphome/esp-arcademachine1.yaml

@@ -0,0 +1,211 @@
+##########################################################################################
+##########################################################################################
+#
+##########################################################################################
+##########################################################################################
+
+
+##########################################################################################
+# SPECIFIC DEVICE VARIABLE SUBSTITUTIONS
+# If NOT using a secrets file, just replace these with the passwords etc (in quotes)
+##########################################################################################
+substitutions:
+  # Device Naming
+  device_name: "esp-arcademachine1"
+  friendly_name: "Arcade Cabinet 1"
+  description_comment: "MAME Arcade 1 (Defender) machine power :: Athom Smart Plug Power V1"
+  device_area: "Downstairs Flat" # Allows ESP device to be automatically linked to an 'Area' in Home Assistant.  
+  
+  # Project Naming
+  project_name: "Athom Technology.Smart Plug V1" # Project Details 
+  project_version: "v1.0"  # Project V denotes release of yaml file, allowing checking of deployed vs latest version
+
+  # Passwords
+  api_key: !secret esp-api_key # unfortunately you can't use substitutions inside secrets names
+  ota_pass: !secret esp-ota_pass # unfortunately you can't use substitutions inside secrets names
+  static_ip_address: !secret esp-arcademachine1_ip
+
+  # Device Settings
+  log_level: "NONE" # Define logging level: NONE, ERROR, WARN, INFO, DEBUG (Default), VERBOSE, VERY_VERBOSE
+  update_interval: "10s" # update time for for general sensors etc
+
+  # Device Settings
+  relay_icon: "mdi:power-socket-au"  
+  current_limit : "10" # Current Limit in Amps. AU Plug = 10. IL, BR, EU, UK, US Plug = 16.
+  
+##########################################################################################
+# PACKAGES: Included Common Packages
+# https://esphome.io/components/packages.html
+##########################################################################################
+packages:
+  ##################################################
+  # MANDATORY packages (won't compile without them!)
+  ##################################################
+
+  #### WIFI, Network (Static/DHCP/IPV6 etc), Fallback AP, Safemode ####
+  common_wifi: !include
+    file: common/network_common.yaml
+    vars:
+      local_device_name: "${device_name}"
+      local_static_ip_address: "${static_ip_address}"
+      local_ota_pass: "${ota_pass}"
+
+  ##################################################
+  # OPTIONAL packages (comment if you don't want them)
+  ##################################################   
+
+  #### HOME ASSISTANT API (choose encryption or no encryption options) ####
+  common_api: !include
+    file: common/api_common.yaml
+    #file: common/api_common_noencryption.yaml
+    vars:
+      local_api_key: "${api_key}"
+  
+  #### WEB PORTAL ####
+  #common_webportal: !include
+  #  file: common/webportal_common.yaml
+
+  #### MQTT ####
+  common_mqtt: !include
+    file: common/mqtt_common.yaml
+    vars:
+      local_device_name: "${device_name}"
+  
+  #### SNTP (Only use if you want/need accurate timeclocks) ####
+  common_sntp: !include
+    file: common/sntp_common.yaml
+
+  #### DIAGNOSTICS Lite Sensors ####
+  common_lite_sensors: !include
+    file: common/sensors_common_lite.yaml
+
+  #### DIAGNOSTICS General Sensors ####
+  common_general_sensors: !include
+    file: common/sensors_common.yaml
+
+  #### DEBUGGING Sensors ####
+  # A count of various resets
+  #common_resetcount_debugging: !include
+  #  file: common/resetcount_common.yaml
+
+  # Device Specific included packages
+  common_athompowermonV1: !include
+    file: common/athompowermonv1_common.yaml
+    vars:
+      local_friendly_name: "${friendly_name}"
+      local_current_limit: "${current_limit}"
+
+##########################################################################################
+# ESPHome
+# https://esphome.io/components/esphome.html
+##########################################################################################
+esphome:
+  name: "${device_name}"
+  friendly_name: "${friendly_name}"
+  comment: "${description_comment}" #Appears on the esphome page in HA
+  area: "${device_area}"  
+  name_add_mac_suffix: False
+  min_version: 2024.6.0
+  project:
+    name: "${project_name}"
+    version: "${project_version}"
+
+
+##########################################################################################
+# ESP Platform and Framework
+# https://esphome.io/components/esp32.html
+##########################################################################################
+esp8266:
+  board: esp8285
+  restore_from_flash: true # mainly for calculating cumulative energy, but not that important here
+  #framework:
+  #  version: 2.7.4
+
+preferences:
+  flash_write_interval: 10min
+
+#mdns:
+#  disabled: True # binary size saving
+
+##########################################################################################    
+# ESPHome Logging Enable
+# https://esphome.io/components/logger.html
+########################################################################################## 
+logger:
+  level: "${log_level}"  #INFO Level suggested, or DEBUG for testing
+  baud_rate: 0 #set to 0 for no logging via UART, needed if you are using it for other serial things (eg PZEM)
+  #esp8266_store_log_strings_in_flash: false
+  #tx_buffer_size: 64
+
+##########################################################################################
+# Global Variables for use in automations etc
+# https://esphome.io/guides/automations.html?highlight=globals#global-variables
+##########################################################################################
+globals:
+
+  # Tracks the time (in seconds from midnight) at the previous boot
+  - id: last_boot_time_s
+    type: int
+    restore_value: true
+    initial_value: "0"
+
+  # Counts how many consecutive boots have occurred (within X seconds)
+  - id: boot_count
+    type: int
+    restore_value: true
+    initial_value: "0"
+
+  ####################################################
+  # boost_timer: counts minutes in BOOST mode
+  # After 'boost_duration' minutes, revert to TIMER.
+  ####################################################
+  - id: boost_timer
+    type: int
+    restore_value: true
+    initial_value: "0"
+
+##########################################################################################
+# BINARY SENSORS
+# https://esphome.io/components/binary_sensor/
+##########################################################################################
+binary_sensor:
+  - platform: gpio
+    pin:
+      number: GPIO03
+      mode: INPUT_PULLUP
+      inverted: true
+    name: "Power Button"
+    id: power_button
+    filters:
+      - delayed_on: 20ms
+    on_click:
+      - min_length: 20ms
+        max_length: 500ms
+        then:
+          - lambda: |-
+              if (id(relay).state) {
+                // Relay is ON: turn it OFF and set mode to 2 (TIMER)
+                id(relay).turn_off();
+              } else {
+                // Relay is OFF: turn it ON and set mode to 3 (BOOST)
+                id(relay).turn_on();
+              }
+  
+  - platform: template
+    name: "Relay Status"
+    lambda: |-
+      return id(relay).state;
+
+#################################################################################################
+# SWITCH COMPONENT
+# https://esphome.io/components/switch/
+#################################################################################################
+switch:
+  - platform: gpio
+    name: "Power Output"
+    pin: GPIO14
+    id: relay
+    restore_mode: RESTORE_DEFAULT_OFF       # Ensures the relay is restored (or off) at boot
+    #internal: true                # Hides the switch from Home Assistant
+    icon: "${relay_icon}" 
+    

esphome/esp-athombulbflasher.yaml

@@ -141,6 +141,7 @@ wifi:
     ssid: ${devicename} AP
     password: ${fallback_ap_password}
     ap_timeout: 30min # Time until it brings up fallback AP. default is 1min
+  min_auth_mode: WPA2
 
 captive_portal:  # extra fallback mechanism for when connecting if the configured WiFi fails
   

esphome/esp-bedrm2fanswitch.yaml

@@ -168,6 +168,7 @@ binary_sensor:
       number: GPIO16
       mode: INPUT
       inverted: True
+    use_interrupt: false # This pin doesn't support interrupts so use polling.  Only supresses a warning.
     name: "Button 1: ${switch_1_name}"
     on_press:
       - mqtt.publish:

esphome/esp-bedrm2lights.yaml

@@ -144,6 +144,7 @@ binary_sensor:
       number: GPIO16
       mode: INPUT
       inverted: True
+    use_interrupt: false # GPIO16 pin doesn't support interrupts so use polling.  Only supresses a warning.  
     name: "Button 1: ${switch_1_name}"
     on_press:
       - switch.toggle: Relay_1

esphome/esp-bedrm3fanswitch.yaml

@@ -121,8 +121,8 @@ esphome:
     build_flags:
       - "-Os"                   # optimize for size
       - "-Wl,--gc-sections"     # drop unused code/data
-      - "-fno-exceptions"       # strip C++ exceptions
+      #- "-fno-exceptions"       # strip C++ exceptions
-      - "-fno-rtti"             # strip C++ RTTI
+      #- "-fno-rtti"             # strip C++ RTTI
 #  on_boot:       
 #    priority: 200
 #    then:
@@ -170,6 +170,7 @@ binary_sensor:
       number: GPIO16
       mode: INPUT
       inverted: True
+    use_interrupt: false # GPO16 pin doesn't support interrupts so use polling.  Only supresses a warning.
     name: "Button 1: ${switch_1_name}"
     on_press:
       - mqtt.publish:

esphome/esp-bedrm3lights.yaml

@@ -168,6 +168,7 @@ binary_sensor:
         input: true
         pullup: false   # set to true if you need an internal pull-up
       inverted: true
+    use_interrupt: false # GPIO16 pin doesn't support interrupts so use polling.  Only supresses a warning.  
     name: "Button 1: ${switch_1_name}"
     filters:
       - delayed_on: 30ms

esphome/esp-breakfastbarleds.yaml

@@ -341,7 +341,7 @@ switch:
   # Ramp-aware ON/OFF for HA (asymmetric, eased; no bounce)
   - platform: template
     id: mosfet_ramp_switch
-    name: "${friendly_name} Fade Up/Down"
+    name: "${friendly_name} Fade Up-Down"
     icon: mdi:led-strip-variant
     lambda: |-
       return id(ramp_switch_target_on);

esphome/esp-centralstairs-bottom.yaml

@@ -218,6 +218,7 @@ binary_sensor:
       number: GPIO16
       mode: INPUT
       inverted: True
+    use_interrupt: false # GPIO16 pin doesn't support interrupts so use polling.  Only supresses a warning.  
     filters:
       - delayed_on: 30ms
       - delayed_off: 30ms

esphome/esp-centralstairs-top.yaml

@@ -218,6 +218,7 @@ binary_sensor:
       number: GPIO16
       mode: INPUT
       inverted: True
+    use_interrupt: false # GPIO16 pin doesn't support interrupts so use polling.  Only supresses a warning.  
     filters:
       - delayed_on: 30ms
       - delayed_off: 30ms

esphome/esp-dinpowermonitor-pmb.yaml

@@ -108,16 +108,18 @@ esphome:
       # Restore "Last Trip" text from persisted epoch (if any)
       - lambda: |-
           if (id(last_trip_epoch) > 0) {
-            auto t = time::ESPTime::from_epoch_local(id(last_trip_epoch));
+            time_t tt = (time_t) id(last_trip_epoch);
+            struct tm tm;
+            localtime_r(&tt, &tm);
             char buf[24];
-            t.strftime(buf, sizeof(buf), "%Y-%m-%d %H:%M:%S");
+            strftime(buf, sizeof(buf), "%Y-%m-%d %H:%M:%S", &tm);
             id(ts_last_trip).publish_state(buf);
           } else {
             id(ts_last_trip).publish_state("Never");
           }
       # Apply Power Restore Mode selector (Always ON / Always OFF / Previous State)
       - lambda: |-
-          std::string mode = id(sel_restore_mode).state;
+          std::string mode = id(sel_restore_mode).current_option();
           if (mode == "Always ON") {
             id(relay_virtual).turn_on();
           } else if (mode == "Always OFF") {
@@ -151,6 +153,7 @@ status_led:
   pin:
     number: GPIO8
     inverted: true
+    ignore_strapping_warning: true # GPIO08: This just supresses a warning, we know what we are doing
 
 ##########################################################################################
 # UART BUS
@@ -550,6 +553,7 @@ binary_sensor:
       number: GPIO9
       mode: INPUT_PULLUP
       inverted: true
+      ignore_strapping_warning: true # GPIO09: This just supresses a warning, we know what we are doing
     name: "${button_1_name}"
     on_press:
       - switch.toggle: relay_virtual
@@ -743,7 +747,7 @@ script:
                 if (f > 1.0f) f = 1.0f;
                 int slow_ms = ${led_flash_slow_ms};
                 int fast_ms = ${led_flash_fast_ms};
-                if (slow_ms < fast_ms) { int t = slow_ms; slow_ms = fast_ms; fast_ms = t; }  # ensure slow >= fast
+                if (slow_ms < fast_ms) { int t = slow_ms; slow_ms = fast_ms; fast_ms = t; }  // ensure slow >= fast
                 int period = slow_ms - (int)((slow_ms - fast_ms) * f);
                 id(_blink_period_ms) = period;
             # Blink with 50% duty cycle at the computed period

esphome/esp-downstairskitchleds.yaml

@@ -352,7 +352,7 @@ switch:
   # Ramp-aware ON/OFF for HA (asymmetric, eased; no bounce)
   - platform: template
     id: mosfet_ramp_switch
-    name: "${friendly_name} Fade Up/Down"
+    name: "${friendly_name} Fade Up-Down"
     icon: mdi:led-strip-variant
     lambda: |-
       return id(ramp_switch_target_on);

esphome/esp-downstbathswitch.yaml

@@ -127,6 +127,7 @@ binary_sensor:
       number: GPIO16
       mode: INPUT
       inverted: True
+    use_interrupt: false # This pin doesn't support interrupts so use polling.  Only supresses a warning.
     name: "Button 1: ${switch_1_name}"
     on_press:
       - switch.toggle: Relay_1

esphome/esp-downstbathtowelrail.yaml

@@ -131,8 +131,8 @@ esphome:
     build_flags:
       - "-Os"                   # optimize for size
       - "-Wl,--gc-sections"     # drop unused code/data
-      - "-fno-exceptions"       # strip C++ exceptions
+      #- "-fno-exceptions"       # strip C++ exceptions
-      - "-fno-rtti"             # strip C++ RTTI
+      #- "-fno-rtti"             # strip C++ RTTI
   on_boot:
     priority: 900  # High priority to run after globals are initialized
     then:
@@ -274,17 +274,6 @@ globals:
     restore_value: true
     initial_value: "2"
 
-  ####################################################
-  # current_mins is set if SNTP is invalid.
-  # We assume user powers on the device at 12:00 noon
-  # => 12 * 60 = 720 minutes from midnight.
-  # Not restored, so it resets each boot.
-  ####################################################
-  - id: current_mins
-    type: int
-    restore_value: false
-    initial_value: "720" # 720 is 12:00 Noon
-
   ####################################################
   # boost_timer: counts minutes in BOOST mode
   # After 'boost_duration' minutes, revert to TIMER.

esphome/esp-downstkitchlights.yaml

@@ -124,6 +124,7 @@ binary_sensor:
       number: GPIO16
       mode: INPUT
       inverted: True
+    use_interrupt: false # This pin doesn't support interrupts so use polling.  Only supresses a warning.
     name: "Button 1: ${switch_1_name}"
     on_press:
       - switch.toggle: Relay_1

esphome/esp-downstloungemain.yaml

@@ -161,6 +161,7 @@ binary_sensor:
       number: GPIO16
       mode: INPUT
       inverted: True
+    use_interrupt: false # This pin doesn't support interrupts so use polling.  Only supresses a warning.
     name: "Button 1: ${switch_1_name}"
     on_press:
       - switch.toggle: Relay_1

esphome/esp-downstloungeoutside.yaml

@@ -145,6 +145,7 @@ binary_sensor:
       number: GPIO16
       mode: INPUT
       inverted: True
+    use_interrupt: false # GPIO16 pin doesn't support interrupts so use polling.  Only supresses a warning.
     name: "Button 1: ${switch_1_name}"
     on_press:
       - switch.toggle: Relay_1

esphome/esp-downstmasterbedrmlights.yaml

@@ -147,6 +147,7 @@ binary_sensor:
       number: GPIO16
       mode: INPUT
       inverted: True
+    use_interrupt: false # GPIO16 pin doesn't support interrupts so use polling.  Only supresses a warning.
     name: "Button 1: ${switch_1_name}"
     on_press:
       - switch.toggle: Relay_1

esphome/esp-entmulti.yaml

@@ -438,6 +438,7 @@ binary_sensor:
       mode:
         input: true
         pullup: true
+      ignore_strapping_warning: true # GPIO15: This just supresses a warning, we know what we are doing
       inverted: True
     filters:
       - delayed_on: 20ms

esphome/esp-entrancebathrmlights.yaml

@@ -142,6 +142,7 @@ binary_sensor:
       number: GPIO16
       mode: INPUT
       inverted: True
+    use_interrupt: false # GPIO16 pin doesn't support interrupts so use polling.  Only supresses a warning.  
     name: "Button 1: ${switch_1_name}"
     on_press:
       - switch.toggle: Relay_1

esphome/esp-flysprayer1.yaml

@@ -1,6 +1,6 @@
 ##########################################################################################
 ##########################################################################################
-# FLY SPRAYER – Sinilink XY-WFUSB (ESP8266/ESP8285) – ESPHome
+# FLY SPRAYER - Sinilink XY-WFUSB (ESP8266/ESP8285) - ESPHome
 #
 # V1.0 2025-05-30 Initial Version
 #
@@ -12,7 +12,7 @@
 # - Sprayer has its own timers, but it fires whenever it is started up, which we utilise here.
 # - Enforce a cooldown so it never double-fires too quickly (Sprayer has some memory)
 # - Operation window select: Night only / Day only / 24 Hours / On / Off.
-# - Randomize each interval by ± a percentage to avoid a perfectly regular pattern.
+# - Randomize each interval by +- a percentage to avoid a perfectly regular pattern.
 # - Red LED (GPIO14, inverted) pulses slowly when idle; goes solid ON during spray.
 # - Green LED (GPIO16) as standard ESPHome status LED.
 # - Has a resettable total spray count, and a daily spray count
@@ -67,8 +67,8 @@ substitutions:
   night_start_h: 21   # 21:00 (9pm)
   night_end_h:   7    # 07:00 (7am)
 
-  # Interval jitter (± percent of selected interval)
+  # Interval jitter (+- percent of selected interval)
-  interval_jitter_pct: 10  # Default ±10%
+  interval_jitter_pct: 10  # Default +-10%
 
 #########################################################################################
 # PACKAGES: Included Common Packages
@@ -142,7 +142,6 @@ esphome:
             id(next_spray_in_text).publish_state("Ready");
         - script.execute: spray_loop
 
-
 ##########################################################################################
 # ESP PLATFORM AND FRAMEWORK
 # https://esphome.io/components/esp8266.html
@@ -310,8 +309,8 @@ select:
     on_value:
       then:
         - logger.log:
-            format: "Spray Interval changed to %s — rescheduling"
+            format: "Spray Interval changed to %s - rescheduling"
-            args: [ 'id(spray_interval).state.c_str()' ]
+            args: [ 'id(spray_interval).current_option().c_str()' ]
         - script.execute: spray_loop
 
   - platform: template
@@ -330,8 +329,8 @@ select:
     on_value:
       then:
         - logger.log:
-            format: "Operation changed to %s — rescheduling"
+            format: "Operation changed to %s - rescheduling"
-            args: [ 'id(spray_operation).state.c_str()' ]
+            args: [ 'id(spray_operation).current_option().c_str()' ]
         - script.execute: spray_loop
 
 ##########################################################################################
@@ -339,7 +338,7 @@ select:
 # https://esphome.io/components/binary_sensor/
 ##########################################################################################
 binary_sensor:
-  # Front panel/local button (GPIO4) – single press triggers a Spray Now (honors cooldown)
+  # Front panel/local button (GPIO4) - single press triggers a Spray Now (honors cooldown)
   - platform: gpio
     id: btn_local
     pin:
@@ -441,20 +440,12 @@ light:
 # https://esphome.io/components/number/
 ##########################################################################################
 
-
 ##########################################################################################
 # SCRIPT COMPONENT
 # https://esphome.io/components/script.html
 # Scripts can be executed nearly anywhere in your device configuration with a single call.
 ##########################################################################################
-# SCRIPTS – main loop, cooldown-safe trigger, and actual spray action
+# SCRIPTS - main loop, cooldown-safe trigger, and actual spray action
-##########################################################################################
-##########################################################################################
-# SCRIPT COMPONENT
-# https://esphome.io/components/script.html
-# Scripts can be executed nearly anywhere in your device configuration with a single call.
-##########################################################################################
-# SCRIPTS – main loop, cooldown-safe trigger, and actual spray action
 ##########################################################################################
 script:
   # Cooldown-checked "Spray Now"
@@ -495,7 +486,7 @@ script:
           brightness: 50%
           effect: red_idle_pulse
 
-  # Scheduler loop – waits a randomized interval, updates countdown text, checks window, then tries to spray
+  # Scheduler loop - waits a randomized interval, updates countdown text, checks window, then tries to spray
   - id: spray_loop
     mode: restart
     then:
@@ -505,7 +496,7 @@ script:
           then:
             # 1) Compute the base interval and randomized wait
             - lambda: |-
-                auto s = id(spray_interval).state;
+                auto s = id(spray_interval).current_option();
                 uint32_t base_sec = 3600; // default 1 hour
                 if (s == "5 minutes")       base_sec = 5 * 60;
                 else if (s == "10 minutes") base_sec = 10 * 60;
@@ -515,13 +506,13 @@ script:
                 else if (s == "2 hours")    base_sec = 2 * 60 * 60;
                 else if (s == "4 hours")    base_sec = 4 * 60 * 60;
 
-                // Jitter ±pct
+                // Jitter +-pct
                 const uint32_t pct = ${interval_jitter_pct};
                 const uint32_t jitter = (base_sec * pct) / 100;
                 const uint32_t span = (jitter * 2u) + 1u;
-                const uint32_t rnd = random_uint32() % span;           // 0..(2*jitter)
+                const uint32_t rnd = random_uint32() % span;            // 0..(2*jitter)
-                const int32_t  delta = (int32_t)rnd - (int32_t)jitter;  // -jitter..+jitter
+                const int32_t  delta = (int32_t) rnd - (int32_t) jitter; // -jitter..+jitter
-                int32_t next_sec = (int32_t)base_sec + delta;
+                int32_t next_sec = (int32_t) base_sec + delta;
                 if (next_sec < 1) next_sec = 1;
 
                 ESP_LOGI("spray", "Next interval: base=%u s, jitter=%u%%, wait=%ld s",
@@ -536,11 +527,11 @@ script:
                 id(next_spray_seconds).publish_state(sec);
                 uint32_t min = (sec + 59u) / 60u;         // minutes, ceiling
                 char buf[16];
-                snprintf(buf, sizeof(buf), "%u min", (unsigned)min);
+                snprintf(buf, sizeof(buf), "%u min", (unsigned) min);
                 std::string countdown_txt(buf);
 
                 // Override text for specific modes
-                auto op = id(spray_operation).state;
+                auto op = id(spray_operation).current_option();
                 char await_buf[16];
 
                 if (op == "Off") {
@@ -594,11 +585,11 @@ script:
                       id(next_spray_seconds).publish_state(sec);
                       uint32_t min = (sec + 59u) / 60u;         // minutes, ceiling
                       char buf[16];
-                      snprintf(buf, sizeof(buf), "%u min", (unsigned)min);
+                      snprintf(buf, sizeof(buf), "%u min", (unsigned) min);
                       std::string countdown_txt(buf);
 
                       // Override text for specific modes
-                      auto op = id(spray_operation).state;
+                      auto op = id(spray_operation).current_option();
                       char await_buf[16];
 
                       if (op == "Off") {
@@ -659,7 +650,7 @@ script:
 
             # 3) Check operation window; if allowed, attempt spray (cooldown enforced inside)
             - lambda: |-
-                auto op = id(spray_operation).state;
+                auto op = id(spray_operation).current_option();
                 bool allowed = false;
 
                 if (op == "Off") {
@@ -699,6 +690,3 @@ script:
                   - script.execute: try_spray_now
 
 
-
-
-

esphome/esp-garagedbcontrols.yaml

@@ -324,6 +324,11 @@ globals:
     type: float
     restore_value: true
     initial_value: "0.0"
+  # Track last day-of-year we snapped so it only happens once per day
+  - id: ev_last_snapshot_doy
+    type: int
+    restore_value: no
+    initial_value: '-1'
 
 # Teleperiod = 60s: publish JSON and advance the window
 interval:
@@ -351,21 +356,25 @@ interval:
             snprintf(buf, sizeof(buf), "{\"EVChargerWhCount\":%.3f}", delta_wh);
             return std::string(buf);
 
-##########################################################################################
+# YESTERDAY ENERGY (device-side snapshot of today's total at end-of-day)
-# YESTERDAY ENERGY (device-side snapshot of today's total at 23:59:59)
+# Uses existing time id(sntp_time) from sntp_common.yaml
-##########################################################################################
+  - interval: 60s
-time:
+    then:
-  - platform: sntp
+      - lambda: |-
-    id: ev_time_for_ev_snap
+          auto now = id(sntp_time).now();
-    on_time:
+          if (!now.is_valid()) return;
-      - seconds: 59
+
-        minutes: 59
+          // Snapshot once per day at 23:59 (minute precision)
-        hours: 23
+          if (now.hour != 23 || now.minute != 59) return;
-        then:
+
-          - lambda: |-
+          // Prevent repeats if this runs multiple times during 23:59
-              // Snapshot today's kWh just before midnight reset
+          if (id(ev_last_snapshot_doy) == now.day_of_year) return;
-              if (isfinite(id(ev_energy_today_kwh).state)) {
+
-                id(ev_energy_yesterday_kwh) = id(ev_energy_today_kwh).state;
+          if (isfinite(id(ev_energy_today_kwh).state)) {
-              }
+            id(ev_energy_yesterday_kwh) = id(ev_energy_today_kwh).state;
+          }
+
+          id(ev_last_snapshot_doy) = now.day_of_year;
+
 
 

esphome/esp-garageentrylights.yaml

@@ -33,7 +33,7 @@ substitutions:
   static_ip_address: !secret esp-garageentrylights_ip
 
   # Device Settings
-  log_level: "INFO" # Define logging level: NONE, ERROR, WARN, INFO, DEBUG (Default), VERBOSE, VERY_VERBOSE
+  log_level: "NONE" # Define logging level: NONE, ERROR, WARN, INFO, DEBUG (Default), VERBOSE, VERY_VERBOSE
   update_interval: "60s" # update time for for general sensors etc
 
   # Default relay restore mode
@@ -82,6 +82,15 @@ packages:
   #diag_debug:       !include common/include_debug_diag_sensors.yaml
   #diag_resetcount:  !include common/include_resetcount_diag_sensors.yaml
 
+# Package item removals
+wifi:
+  min_auth_mode: !remove # The WPA2 only works on esp32/8266
+  reboot_timeout: 15min    # override the selection from from the common package
+  fast_connect: false      # (optional) force off, in case package vars change
+
+mqtt:
+  keepalive: 15s # overriding the value from the common package
+
 #############################################
 # ESPHome
 # https://esphome.io/components/esphome.html
@@ -99,6 +108,9 @@ esphome:
 #    then:
 #      - switch.turn_on: Relay_3
 
+mdns:
+  disabled: true
+
 #############################################
 # BUILD FOR BK CHIPSET
 # bk72xx

esphome/esp-garageentrylights2.yaml

@@ -82,6 +82,15 @@ packages:
   #diag_debug:       !include common/include_debug_diag_sensors.yaml
   #diag_resetcount:  !include common/include_resetcount_diag_sensors.yaml
 
+  # Package item removals
+wifi:
+  min_auth_mode: !remove # The WPA2 only works on esp32/8266
+  reboot_timeout: 15min    # override the selection from from the common package
+  fast_connect: false      # (optional) force off, in case package vars change
+
+mqtt:
+  keepalive: 15s # overriding the value from the common package
+
 #############################################
 # ESPHome
 # https://esphome.io/components/esphome.html

esphome/esp-loungebookshelfleds.yaml

@@ -341,7 +341,7 @@ switch:
   # Ramp-aware ON/OFF for HA (asymmetric, eased; no bounce)
   - platform: template
     id: mosfet_ramp_switch
-    name: "${friendly_name} Fade Up/Down"
+    name: "${friendly_name} Fade Up-Down"
     icon: mdi:led-strip-variant
     lambda: |-
       return id(ramp_switch_target_on);

esphome/esp-loungecabinetleds2.yaml

@@ -346,7 +346,7 @@ switch:
   # Ramp-aware ON/OFF for HA (asymmetric, eased; no bounce)
   - platform: template
     id: mosfet_ramp_switch
-    name: "${friendly_name} Fade Up/Down"
+    name: "${friendly_name} Fade Up-Down"
     icon: mdi:led-strip-variant
     lambda: |-
       return id(ramp_switch_target_on);

esphome/esp-loungemiddleswitch.yaml

@@ -164,6 +164,7 @@ binary_sensor:
       number: GPIO16
       mode: INPUT
       inverted: True
+    use_interrupt: false # This pin doesn't support interrupts so use polling.  Only supresses a warning.
     name: "Button 1: ${switch_1_name}"
     on_multi_click:
 

esphome/esp-loungemoesdimmer2.yaml

@@ -77,6 +77,15 @@ packages:
       local_friendly_name: "${friendly_name}"
       local_update_interval: "${update_interval}"
 
+      # Package item removals
+wifi:
+  min_auth_mode: !remove # The WPA2 only works on esp32/8266
+  reboot_timeout: 15min    # override the selection from from the common package
+  fast_connect: false      # (optional) force off, in case package vars change
+
+mqtt:
+  keepalive: 15s # overriding the value from the common package
+
 #########################################################################################
 # ESPHome
 # https://esphome.io/components/esphome.html

esphome/esp-loungepelmetleds2.yaml

@@ -385,7 +385,7 @@ logger:
 switch:
   - platform: template
     id: mosfet_ramp_switch_a
-    name: "${friendly_name} A Fade Up/Down"
+    name: "${friendly_name} A Fade Up-Down"
     icon: mdi:led-strip-variant
     lambda: |-
       return id(ramp_switch_target_on_A);
@@ -402,7 +402,7 @@ switch:
 
   - platform: template
     id: mosfet_ramp_switch_b
-    name: "${friendly_name} B Fade Up/Down"
+    name: "${friendly_name} B Fade Up-Down"
     icon: mdi:led-strip-variant
     lambda: |-
       return id(ramp_switch_target_on_B);

esphome/esp-loungesouthleftswitch.yaml

@@ -145,6 +145,7 @@ binary_sensor:
       number: GPIO16
       mode: INPUT
       inverted: True
+    use_interrupt: false # This pin doesn't support interrupts so use polling.  Only supresses a warning.
     name: "Button 1: ${switch_1_name}"
     on_press:
       - switch.toggle: Relay_1

esphome/esp-loungesouthrightswitch.yaml

@@ -158,6 +158,7 @@ binary_sensor:
       number: GPIO16
       mode: INPUT
       inverted: True
+    use_interrupt: false # GPO16 pin doesn't support interrupts so use polling.  Only supresses a warning.
     name: "Button 1: ${switch_1_name}"
     on_press:
       - switch.toggle: Relay_1

esphome/esp-mainbathfancombo.yaml

@@ -100,8 +100,8 @@ esphome:
     build_flags:
       - "-Os"                   # optimize for size
       - "-Wl,--gc-sections"     # drop unused code/data
-      - "-fno-exceptions"       # strip C++ exceptions
+      #- "-fno-exceptions"       # strip C++ exceptions
-      - "-fno-rtti"             # strip C++ RTTI
+      #- "-fno-rtti"             # strip C++ RTTI
 #  on_boot:       
 #    priority: 200
 #    then:
@@ -149,6 +149,7 @@ binary_sensor:
       number: GPIO16
       mode: INPUT
       inverted: True
+    use_interrupt: false # GPO16 pin doesn't support interrupts so use polling.  Only supresses a warning.
     name: "Button 1: Extract Fan"
     on_press:
       - switch.toggle: "Relay_1"

esphome/esp-masterbathtowelrail.yaml

@@ -271,16 +271,6 @@ globals:
     restore_value: true
     initial_value: "2"
 
-  ####################################################
-  # current_mins is set if SNTP is invalid.
-  # We assume user powers on the device at 12:00 noon
-  # => 12 * 60 = 720 minutes from midnight.
-  ####################################################
-  - id: current_mins
-    type: int
-    restore_value: false
-    initial_value: "720" # 720 is 12:00 Noon
-
   ####################################################
   # boost_timer: counts minutes in BOOST mode
   # After 'boost_duration' minutes, revert to TIMER.

esphome/esp-officelights copy.yaml.old

@@ -135,6 +135,7 @@ binary_sensor:
       number: GPIO16
       mode: INPUT
       inverted: True
+    use_interrupt: False # GPIO16 pin doesn't support interrupts so use polling.  Only supresses a warning.
     name: "Button 1: ${switch_1_name}"
     on_press:
       - switch.toggle: Relay_1

esphome/esp-officelights.yaml

@@ -135,6 +135,7 @@ binary_sensor:
       number: GPIO16
       mode: INPUT
       inverted: True
+    use_interrupt: False # GPIO16 pin doesn't support interrupts so use polling.  Only supresses a warning.
     name: "Button 1: ${switch_1_name}"
     on_press:
       - switch.toggle: Relay_1

esphome/esp-poollightpower2.yaml

@@ -272,16 +272,6 @@ globals:
     restore_value: true
     initial_value: "2"
 
-  ####################################################
-  # current_mins is set if SNTP is invalid.
-  # We assume user powers on the device at 12:00 noon
-  # => 12 * 60 = 720 minutes from midnight.
-  ####################################################
-  - id: current_mins
-    type: int
-    restore_value: true
-    initial_value: "720" # 720 is 12:00 Noon
-
   ####################################################
   # boost_timer: counts minutes in BOOST mode
   # After 'boost_duration' minutes, revert to TIMER.

packages/ha_summary.yaml

@@ -219,11 +219,21 @@ template:
         unique_id: ha_summary_addons
         icon: mdi:puzzle
         state: >-
-          {% set a = states.update | selectattr('entity_id','in', integration_entities('hassio')) | list %}
+          {% set hassio_updates = (integration_entities('hassio') | list) %}
-          {% set b = states.update | selectattr('attributes.attribution','search','Supervisor') | list %}
+          {% set a = states.update
-          {{ (a + b) | unique | list
+            | selectattr('entity_id','in', hassio_updates)
-             | rejectattr('entity_id','search','^update\\.home_assistant_(core|supervisor|operating_system)_update$')
+            | map(attribute='entity_id')
-             | list | length }}
+            | list %}
+          {% set b = states.update
+            | selectattr('attributes.attribution','defined')
+            | selectattr('attributes.attribution','search','Supervisor')
+            | map(attribute='entity_id')
+            | list %}
+          {% set ids = (a + b)
+            | unique
+            | reject('search','^update\\.home_assistant_(core|supervisor|operating_system)_update$')
+            | list %}
+          {{ ids | length }}
 
       # ---------- HACS updates available (proxy only) ----------
       - name: HA Summary - hacs updates

packages/low_battery_device_quantity.yaml

@@ -61,7 +61,6 @@ template:
                   {% endif %}
                 {% endif %}
               {% endif %}
-            {% endif %}
             {% endfor %}
             {{ ns.e }}
           names: >
@@ -75,6 +74,5 @@ template:
                   {% endif %}
                 {% endif %}
               {% endif %}
-            {% endif %}
             {% endfor %}
             {{ ns.n }}

packages/shower_controls.yaml

@@ -1,7 +1,7 @@
 sensor:
   - platform: derivative
     name: Main Bathroom Humidity Change Rate
-    source: sensor.main_bathroom_environment_zth04_humidity
+    source: sensor.main_bathroom_environment_zth10_humidity_2
     round: 1
     unit_time: s # the resulting "unit_of_measurement" will be %H/s if the sensor.temperate has set %H as its unit
     time_window: "00:00:10" # we look at the change over the last 10 seconds