Edit esp-bedside-panel.yaml

esphome/esp-bedside-panel.yaml

@@ -6,6 +6,7 @@
 # https://home.fox.co.nz/gitea/zorruno/zorruno-homeassistant/src/branch/master/esphome/esp-bedside-panel.yaml
 #:########################################################################################:#
 # VERSIONS:
+# V0.4 2026-07-14 Removed MIPI display test after setup watchdog boot loop; retained backlight-only test
 # V0.3 2026-07-14 Added backlight control and first MIPI display text test
 # V0.2 2026-07-14 Added ESP32 hosted WiFi via ESP32-C6 co-processor
 # V0.1 2026-07-14 Initial ESPHome bring-up for Guition JC1060P470C_I_W_Y ESP32-P4 panel
@@ -27,16 +28,17 @@
 #:########################################################################################:#
 # OPERATION NOTES:
 # - Flash this to the ESP32-P4 side of the board.
-# - This version is intended to confirm:
+# - This version tests only:
-#   - ESPHome compile
+#   - ESPHome boot
-#   - USB/OTA flashing
+#   - Hosted WiFi through the ESP32-C6
-#   - Serial logging
+#   - Home Assistant API
-#   - WiFi connection via ESP32-C6 hosted co-processor
+#   - GPIO23 backlight PWM
-#   - Home Assistant API connection
+#   - Backlight light entity in Home Assistant
-#   - Backlight entity appears in Home Assistant
+# - The MIPI display component has been temporarily removed because V0.3
-#   - Display lights and shows simple test text
+#   triggered a watchdog reset during setup.
-# - This version intentionally does not yet configure:
+# - This version intentionally does not configure:
 #   - Ethernet
+#   - Display image generation
 #   - Touchscreen
 #   - LVGL
 #   - Ambient light sensor
@@ -44,10 +46,9 @@
 #   - Camera
 #:########################################################################################:#
 # OFFLINE NOTES:
-# - This version has no local control logic yet.
+# - Backlight control is exposed locally by ESPHome and through Home Assistant.
-# - This version does not require Home Assistant to boot.
+# - The panel should remain connected even though no image is drawn.
-# - Display test should run locally once the device boots.
+# - The physical panel may remain blank while the backlight is tested.
-# - Home Assistant API will connect only once hosted WiFi is working.
 #:########################################################################################:#
 
 #:########################################################################################:#
@@ -59,12 +60,12 @@ substitutions:
   # Device Naming
   device_name: "esp-bedside-panel"
   friendly_name: "ESP Bedside Panel"
-  description_comment: "Guition JC1060P470C_I_W_Y ESP32-P4 7 inch bedside control panel. Backlight and display test. (Layout V1.1)"
+  description_comment: "Guition JC1060P470C_I_W_Y ESP32-P4 7 inch bedside control panel. Backlight-only test following MIPI setup watchdog. (Layout V1.1)"
   device_area: "Bedroom" # Allows ESP device to be automatically linked to an 'Area' in Home Assistant.
 
   # Project Naming
   project_name: "Guition.JC1060P470C_I_W_Y" # Project Details
-  project_version: "v0.3"  # Project V denotes release of yaml file, allowing checking of deployed vs latest version
+  project_version: "v0.4" # Project V denotes release of yaml file, allowing checking of deployed vs latest version
 
   # Passwords & Secrets
   api_key: !secret esp-api_key # unfortunately you can't use substitutions inside secrets names
@@ -74,10 +75,9 @@ substitutions:
   log_level: "INFO" # Define logging level: NONE, ERROR, WARN, INFO, DEBUG (Default), VERBOSE, VERY_VERBOSE
   update_interval: "60s" # update time for general sensors etc
 
-  # Display Settings
+  # Backlight Settings
-  display_width: "1024"
+  backlight_pin: "23"
-  display_height: "600"
+  backlight_frequency: "1220Hz"
-  display_rotation: "90"
 
 #:########################################################################################:#
 # PACKAGES:
@@ -86,7 +86,6 @@ substitutions:
 #:########################################################################################:#
 packages:
   #### WIFI, Network DHCP, Fallback AP, Safemode ####
-  # NOTE:
   # This board does not have native WiFi in the ESP32-P4 itself.
   # The esp32_hosted section below exposes the ESP32-C6 co-processor as WiFi.
   common_wifi: !include
@@ -103,26 +102,18 @@ packages:
       local_api_key: "${api_key}"
 
   #### MQTT ####
-  # NOTE:
-  # Leave MQTT disabled for initial bring-up. Add later if needed.
   #common_mqtt: !include
   #  file: common/mqtt_common.yaml
   #  vars:
   #    local_device_name: "${device_name}"
 
   #### WEB PORTAL ####
-  # NOTE:
-  # Leave disabled until WiFi/API/display are confirmed.
   #common_webportal: !include common/webportal_common_nopass.yaml
 
   #### SNTP (Only use if you want/need accurate timeclocks) ####
-  # NOTE:
-  # For the clock page later, we will probably use Home Assistant time first.
   #common_sntp: !include common/sntp_common.yaml
 
   #### DIAGNOSTICS Sensors ####
-  # NOTE:
-  # Keep common diagnostic packages disabled until first display test is confirmed.
   #diag_basic: !include common/include_basic_diag_sensors.yaml
   #diag_more: !include common/include_more_diag_sensors.yaml
   #diag_debug: !include common/include_debug_diag_sensors.yaml
@@ -135,7 +126,7 @@ packages:
 esphome:
   name: "${device_name}"
   friendly_name: "${friendly_name}"
-  comment: "${description_comment}" # Appears on the esphome page in HA
+  comment: "${description_comment}" # Appears on the ESPHome page in HA
   area: "${device_area}"
   project:
     name: "${project_name}"
@@ -153,7 +144,7 @@ esp32:
   framework:
     type: esp-idf
     advanced:
-      enable_idf_experimental_features: yes
+      enable_idf_experimental_features: true
     sdkconfig_options:
       CONFIG_SPIRAM_XIP_FROM_PSRAM: "y"
 
@@ -235,9 +226,9 @@ time:
 #:########################################################################################:#
 output:
   - platform: ledc
-    pin: 23
+    pin: ${backlight_pin}
     id: backlight_output
-    frequency: 1220Hz
+    frequency: "${backlight_frequency}"
 
 #:########################################################################################:#
 # LIGHT:
@@ -246,43 +237,12 @@ output:
 light:
   - platform: monochromatic
     output: backlight_output
-    name: "${friendly_name} Backlight"
+    name: "Backlight"
     id: display_backlight
-    restore_mode: ALWAYS_ON
+    icon: "mdi:brightness-6"
+    restore_mode: RESTORE_DEFAULT_ON
     default_transition_length: 0s
 
-#:########################################################################################:#
-# DISPLAY:
-# https://esphome.io/components/display/mipi_dsi.html
-#:########################################################################################:#
-display:
-  - platform: mipi_dsi
-    model: JC1060P470
-    id: main_display
-    rotation: ${display_rotation}
-    dimensions:
-      width: ${display_width}
-      height: ${display_height}
-    update_interval: 1s
-    lambda: |-
-      it.fill(Color::BLACK);
-      it.printf(300, 210, id(font_large), Color::WHITE, "ESPHome OK");
-      it.printf(300, 280, id(font_small), Color::WHITE, "JC1060P470C_I_W_Y");
-      it.printf(300, 330, id(font_small), Color::WHITE, "WiFi + Display Test");
-
-#:########################################################################################:#
-# FONTS:
-# https://esphome.io/components/font.html
-#:########################################################################################:#
-font:
-  - file: "gfonts://Roboto"
-    id: font_large
-    size: 48
-
-  - file: "gfonts://Roboto"
-    id: font_small
-    size: 28
-
 #:########################################################################################:#
 # SENSORS:
 # https://esphome.io/components/sensor/