root
195 lines
8.3 KiB
YAML
195 lines
8.3 KiB
YAML
##########################################################################################
|
||
##########################################################################################
|
||
# Moes Mains Dimmer
|
||
# Mains dimmer 150W single channel - Moes Wi-Fi Dimmer Module
|
||
# Module swapped to a ESP-02S module (from a Tuya WB2S)
|
||
#
|
||
# V1.0 2025-09-05 First Rev
|
||
##########################################################################################
|
||
#
|
||
# NOTES RE TUYA COMMS FOR THIS MODULE
|
||
# - Toggle DP1 (switch) to 1/0 for ON/OFF — the dimmer’s MCU does the smooth ramp itself over a few seconds.
|
||
# - We set DP2 (brightness) on a 0–1000 scale; this is the actual brightness level your firmware uses.
|
||
# - We read DP2 back as a sensor (and also show a % view) so we can see the live target the MCU is using.
|
||
# - DP3 is exposed only as an optional minimum-brightness limit; not touched during normal dimming unless you tune the low end.
|
||
# - It appears that 11 is the lowest DP3 raw value. Brightness of 1% sets this, and 2% ramps it to 19.
|
||
# - 50% brightness is 501, so it is pretty linear (you can't set Gamma, see below - I guess you could script it though)
|
||
# - DP4 (mode) exists but left alone (unless you want to experiment with load type/behavior). I can't see it do anything. Disabled by default in HA.
|
||
# - gamma_correct supposedly remaps the HA slider (no Tuya traffic) BUT it must be set to 1 or weird behaviour (keeps ramping to 0)
|
||
# - setting logs to DEBUG will show what is happening with Tuya commands
|
||
#
|
||
##########################################################################################
|
||
##########################################################################################
|
||
|
||
##########################################################################################
|
||
# SPECIFIC DEVICE VARIABLE SUBSTITUTIONS
|
||
# If NOT using a secrets file, just replace these with the passwords etc (in quotes)
|
||
##########################################################################################
|
||
substitutions:
|
||
# Device Naming
|
||
device_name: "esp-loungemoesdimmer1"
|
||
friendly_name: "Lounge Lighting Moes Dimmer 1"
|
||
description_comment: "tba"
|
||
device_area: "Lounge" # Allows ESP device to be automatically linked to an 'Area' in Home Assistant.
|
||
|
||
# Project Naming
|
||
project_name: "Generic ESP8266.ESP-02S" # Project Details
|
||
project_version: "v1.0" # Project V denotes release of yaml file, allowing checking of deployed vs latest version
|
||
|
||
# Passwords & Secrets
|
||
api_key: !secret esp-api_key # unfortunately you can't use substitutions inside secrets names
|
||
ota_pass: !secret esp-ota_pass # unfortunately you can't use substitutions inside secrets names
|
||
static_ip_address: !secret esp-loungemoesdimmer1_ip
|
||
|
||
# Device Settings
|
||
#relay_icon: "mdi:lightbulb-group"
|
||
log_level: "INFO" # Define logging level: NONE, ERROR, WARN, INFO, DEBUG (Default), VERBOSE, VERY_VERBOSE
|
||
update_interval: "60s" # update time for for general sensors etc
|
||
|
||
#########################################################################################
|
||
# PACKAGES: Included Common Packages
|
||
# https://esphome.io/components/packages.html
|
||
##########################################################################################
|
||
# Comment some of these out where not needed, eg MQTT, Web portal, SNTP, General Sensors
|
||
##########################################################################################
|
||
packages:
|
||
common_wifi: !include
|
||
file: common/network_common.yaml
|
||
vars:
|
||
local_device_name: "${device_name}"
|
||
local_static_ip_address: "${static_ip_address}"
|
||
local_ota_pass: "${ota_pass}"
|
||
common_api: !include
|
||
file: common/api_common.yaml
|
||
vars:
|
||
local_api_key: "${api_key}"
|
||
#common_webportal: !include
|
||
# file: common/webportal_common.yaml
|
||
common_mqtt: !include
|
||
file: common/mqtt_common.yaml
|
||
vars:
|
||
local_device_name: "${device_name}"
|
||
common_sntp: !include
|
||
file: common/sntp_common.yaml
|
||
common_general_sensors: !include
|
||
file: common/sensors_common.yaml
|
||
vars:
|
||
local_friendly_name: "${friendly_name}"
|
||
local_update_interval: "${update_interval}"
|
||
|
||
#########################################################################################
|
||
# ESPHome
|
||
# https://esphome.io/components/esphome.html
|
||
#########################################################################################
|
||
esphome:
|
||
name: "${device_name}"
|
||
friendly_name: "${friendly_name}"
|
||
comment: "${description_comment}" # Appears on the esphome page in HA
|
||
area: "${device_area}"
|
||
project:
|
||
name: "${project_name}"
|
||
version: "${project_version}"
|
||
|
||
#########################################################################################
|
||
# ESP Platform and Framework
|
||
# https://esphome.io/components/esp32.html
|
||
#########################################################################################
|
||
esp8266:
|
||
board: esp01_1m
|
||
#early_pin_init: False # Initialise pins early to known values. Recommended false where switches are involved. Defaults to True.
|
||
board_flash_mode: dout # Default is dout
|
||
|
||
#########################################################################################
|
||
# ESPHome Logging Enable
|
||
# https://esphome.io/components/logger.html
|
||
#############################################
|
||
logger:
|
||
level: "${log_level}" #INFO Level suggested, or DEBUG for testing
|
||
baud_rate: 0 #set to 0 for no logging via UART, needed if you are using it for other serial things (eg PZEM)
|
||
#esp8266_store_log_strings_in_flash: false
|
||
#tx_buffer_size: 64
|
||
|
||
#########################################################################################
|
||
# STATUS LED
|
||
# https://esphome.io/components/status_led.html
|
||
#########################################################################################
|
||
status_led:
|
||
pin:
|
||
number: GPIO2
|
||
inverted: yes
|
||
|
||
#########################################################################################
|
||
# UART COMPONENT
|
||
# https://esphome.io/components/uart/
|
||
#########################################################################################
|
||
uart:
|
||
# Needed for the Tuya component.
|
||
# This UART talks to the coprocessing tuya chip
|
||
tx_pin: GPIO1
|
||
rx_pin: GPIO3
|
||
baud_rate: 9600
|
||
|
||
#########################################################################################
|
||
# TUYA MCU COMPONENT
|
||
# https://esphome.io/components/tuya/
|
||
#########################################################################################
|
||
tuya:
|
||
# logger baud_rate must be 0
|
||
id: tuyamcu
|
||
|
||
##########################################################################################
|
||
# LIGHT COMPONENT
|
||
# https://esphome.io/components/light/
|
||
##########################################################################################
|
||
light:
|
||
- platform: tuya
|
||
name: "Lounge Lighting Moes Dimmer 1"
|
||
switch_datapoint: 1 # ON/OFF
|
||
dimmer_datapoint: 2 # <-- CHANGED: brightness is DP2 on your unit
|
||
#min_value_datapoint: 3 # optional; comment this out if it misbehaves
|
||
min_value: 0
|
||
max_value: 1000
|
||
gamma_correct: 1.0
|
||
default_transition_length: 0s
|
||
|
||
##########################################################################################
|
||
# SENSOR COMPONENT
|
||
# https://esphome.io/components/sensor/
|
||
##########################################################################################
|
||
sensor:
|
||
# The raw value sent over the UART
|
||
# Listed as a dignostic, so will appear with the other diags in HA
|
||
- platform: tuya
|
||
id: dp2_brightness_raw
|
||
name: "Brightness (DP2 raw)"
|
||
sensor_datapoint: 2
|
||
entity_category: diagnostic
|
||
# Raw value as a percentage of max
|
||
- platform: template
|
||
name: "Brightness (%)"
|
||
unit_of_measurement: "%"
|
||
accuracy_decimals: 0
|
||
update_interval: 2s
|
||
lambda: |-
|
||
if (isnan(id(dp2_brightness_raw).state)) return NAN;
|
||
return (id(dp2_brightness_raw).state / 1000.0f) * 100.0f;
|
||
|
||
##########################################################################################
|
||
# SELECT COMPONENT
|
||
# https://esphome.io/components/select/
|
||
##########################################################################################
|
||
select:
|
||
# Experimental
|
||
- platform: tuya
|
||
id: dp4_mode
|
||
name: "DP4 Mode (experiment)"
|
||
enum_datapoint: 4
|
||
options:
|
||
0: "Mode 0"
|
||
1: "Mode 1"
|
||
2: "Mode 2"
|
||
3: "Mode 3"
|
||
4: "Mode 4"
|
||
255: "Default/Unknown"
|
||
entity_category: config
|
||
disabled_by_default: true |