pmb 6 button switch now V1.1

esphome/esp-6buttontest-pmb.yaml

@@ -20,10 +20,10 @@
 # OPERATION (as at V1.1)
 # 1. Buttons 1-3: These toggle a virtual relay (v_relay1 to 3) and also turn on the 
 #    associated LED when pressed.  Inputs are debounced.
-# 2. Button 4: As with buttons1-3,but also if double pressed, the v_relay only 
+# 2. Button 4: As with buttons 1-3,but also if double pressed, the v_relay only 
 #    stays on for a short period (default 30s) then switches off.  The LED fast flashes.
 #    If it is held down, it stays on for longer (1hr default) and the LED slow flashes.
-# 3. Button 5: As with Buttons1-3 BUT if double pressed, a different v_relay switches on 
+# 3. Button 5: As with Buttons 1-3 BUT if double pressed, a different v_relay switches on 
 #    (5B) and the LED slowly pulses.  If held down for 2 seconds, a 3rd v_relay switches
 #    on (5C) and the LED fast pulses. The 3 v_relays are exclusive, only one can be 
 #    on at a time.
@@ -33,13 +33,13 @@
 # 6. Power Loss: LEDs and v_relays are restored on power loss (restore settings saved 
 #    every 10s). If v_relay4 was turned on with a timer (double press or hold), the 
 #    state isn't restored on power loss.
-# 7. There is an overall brigntness slider/variable.  This allows the LEDs (except when 
+# 7. There is an overall brightness slider/variable.  This allows the LEDs (except when 
 #    flashing) to have a maximum brightness (eg for night mode)
 #
 # NOTES
 # 1. To Flash via ESPHome, you likely have to connect to the computer, start the flash 
 #    then hold down I00 button.  I think GPIO12 connection is preventing the flash process.
-# 2. OTA flash to an Existing Tasmota device is likely a bit hard with and ESP32 as they
+# 2. OTA flash to an existing Tasmota device is likely a bit hard with and ESP32 as they
 #    expect a signed Tasmota binary... and partition layout needs to be fixed anyway
 # 3. ESPHome warns on compiling: "legacy adc driver is deprecated, please migrate to use 
 #    esp_adc/adc_oneshot.h and esp_adc/adc_continuous.h for oneshot mode and continuous mode 
@@ -105,7 +105,6 @@ substitutions:
   log_level: "INFO" # Define logging level: NONE, ERROR, WARN, INFO, DEBUG (Default), VERBOSE, VERY_VERBOSE
   update_interval: "60s" # update time for for general sensors etc
   pwm_freq: "1000Hz" # ESPHome default is 1000Hz, but will go much higher... (not much point for a switch LED)
-  ledc_bits: "12" # ESPHome default resolution is 12 bits
 
   # Network reconnect every x hours to ensure best access point
   # This is my own script.  No need to use if only one AP or it is always fixed.
@@ -185,9 +184,9 @@ wifi:
     password: ${fallback_ap_password}
     ap_timeout: 10min # Time until it brings up fallback AP. default is 1min
   # Allow rapid re-connection to previously connect WiFi SSID, skipping scan of all SSID
-  fast_connect: "${wifi_fast_connect}"
+  fast_connect: ${wifi_fast_connect}
   # Define dns domain / suffix to add to hostname
-  domain: "${dns_domain}"
+  domain: ${dns_domain}
 
 #captive_portal: # extra fallback mechanism for when connecting if the configured WiFi fails
 
@@ -225,8 +224,8 @@ mqtt:
   topic_prefix: ${mqtt_topic}/${device_name}
   username: ${mqtt_username}
   password: ${mqtt_password}
-  discovery: False # enable entity discovery (true is default)
-  discover_ip: False # enable device discovery (true is default)
+  discovery: false # enable entity discovery (true is default)
+  discover_ip: false # enable device discovery (true is default)
   id: mqtt_client
   reboot_timeout: 0s  # same for MQTT
 
@@ -365,11 +364,11 @@ status_led:
 ##########################################################################################
 # SCRIPT COMPONENT
 # https://esphome.io/components/script.html
-# Scripts can be executednearly anywhere in your device configuration with a single call.
+# Scripts can be executed nearly anywhere in your device configuration with a single call.
 ##########################################################################################
 script:
   # Restart Networking every x hours + rand mins.  Starts on reboot and always runs
-  # This ensure that the device is connected to the best AP, but no need for it
+  # This ensures that the device is connected to the best AP, but no need for it
   # if one AP and it is always reliable.
   - id: random_reconnect
     mode: restart
@@ -921,9 +920,8 @@ sensor:
     name: "WiFi (%):"
     filters:
       - lambda: return min(max(2 * (x + 100.0), 0.0), 100.0);
-    unit_of_measurement: "% Max"
+    unit_of_measurement: "%"
     entity_category: "diagnostic"
-    device_class: ""
 
 ##########################################################################################
 # TEXT SENSOR COMPONENT