1019 lines
36 KiB
YAML
1019 lines
36 KiB
YAML
##########################################################################################
|
|
##########################################################################################
|
|
# PMB Electronics 6 Button ESP32 Switch
|
|
#
|
|
# V1.1 2025-08-06 Various function updates, Ext V calibrated (for my unit)
|
|
# V1.0 2025-08-04 Initial Version
|
|
##########################################################################################
|
|
# PMB Product Details Page https://rcbeacon.com/blog/?p=5488
|
|
#
|
|
# DEVICE GPIO
|
|
# ------------------------------------------
|
|
# GPIO36 ADC1 (knob) GPIO39 ADC2 (Supply V)
|
|
# GPIO19 Button1 GPIO21 LED1
|
|
# GPIO35 Button2 GPIO25 LED2
|
|
# GPIO05 Button3 GPIO18 LED3
|
|
# GPIO33 Button4 GPIO26 LED4
|
|
# GPIO16 Button5 GPIO17 LED5
|
|
# GPIO12 Button6 GPIO13 LED6 (6 button/led may not be Populated)
|
|
#
|
|
# OPERATION (as at V1.1)
|
|
# 1. Buttons 1-3: These toggle a virtual relay (v_relay1 to 3) and also turn on the
|
|
# associated LED when pressed. Inputs are debounced.
|
|
# 2. Button 4: As with buttons 1-3,but also if double pressed, the v_relay only
|
|
# stays on for a short period (default 30s) then switches off. The LED fast flashes.
|
|
# If it is held down, it stays on for longer (1hr default) and the LED slow flashes.
|
|
# 3. Button 5: As with Buttons 1-3 BUT if double pressed, a different v_relay switches on
|
|
# (5B) and the LED slowly pulses. If held down for 2 seconds, a 3rd v_relay switches
|
|
# on (5C) and the LED fast pulses. The 3 v_relays are exclusive, only one can be
|
|
# on at a time.
|
|
# 4. The knob gives a reported value of 0-100% when turned (as well as the adc value).
|
|
# this can be calibrated in the substitutions section
|
|
# 5. The system supply voltage is reported (~10-20V).
|
|
# 6. Power Loss: LEDs and v_relays are restored on power loss (restore settings saved
|
|
# every 10s). If v_relay4 was turned on with a timer (double press or hold), the
|
|
# state isn't restored on power loss.
|
|
# 7. There is an overall brightness slider/variable. This allows the LEDs (except when
|
|
# flashing) to have a maximum brightness (eg for night mode)
|
|
#
|
|
# NOTES
|
|
# 1. To Flash via ESPHome, you likely have to connect to the computer, start the flash
|
|
# then hold down I00 button. I think GPIO12 connection is preventing the flash process.
|
|
# 2. OTA flash to an existing Tasmota device is likely a bit hard with and ESP32 as they
|
|
# expect a signed Tasmota binary... and partition layout needs to be fixed anyway
|
|
# 3. ESPHome warns on compiling: "legacy adc driver is deprecated, please migrate to use
|
|
# esp_adc/adc_oneshot.h and esp_adc/adc_continuous.h for oneshot mode and continuous mode
|
|
# drivers respectively" [-Wcpp]" (I'm not bothered with this)
|
|
# 4. Normally I'd include SNTP for timing/scheduling functions, and uptime diagnostics etc.
|
|
# I have commented this out in the packages section as not sure it is really needed here.
|
|
#
|
|
##########################################################################################
|
|
##########################################################################################
|
|
|
|
##########################################################################################
|
|
# SPECIFIC DEVICE VARIABLE SUBSTITUTIONS
|
|
# USUALLY YOU WILL ONLY NEED TO CHANGE VALUES UNDER THIS SECTION
|
|
# If NOT using a secrets file, just replace "!secret my_key" with the password etc (in quotes)
|
|
##########################################################################################
|
|
substitutions:
|
|
# Device Naming
|
|
device_name: "esp-6buttontest-pmb" # the filename should be the device_name.yaml
|
|
friendly_name: "PMB Light Switch Test"
|
|
description_comment: "Multi Button Wallswitch in standard AU/NZ flush size. In this case 5 Buttons with LEDs and one Knob"
|
|
device_area: "Lounge" # Allows ESP device to be automatically linked to an 'Area' in Home Assistant.
|
|
|
|
# Wifi details
|
|
wifi_ssid: !secret ha_wifi_ssid
|
|
wifi_password: !secret ha_wifi_password
|
|
fallback_ap_password: !secret fallback_ap_password # if it doesn't connect, it will create its own AP
|
|
|
|
# Passwords
|
|
api_key: !secret esp-api_key # unfortunately you can't use substitutions inside secrets names
|
|
ota_pass: !secret esp-ota_pass # unfortunately you can't use substitutions inside secrets names
|
|
static_ip_address: !secret esp-6buttontest-pmb_ip
|
|
|
|
# Add these if we are giving it a static ip, or remove them in the Wifi section
|
|
static_ip_subnet: !secret ha_wifi_subnet
|
|
static_ip_gateway: !secret ha_wifi_gateway
|
|
static_ip_dns1: !secret ha_wifi_dns1
|
|
static_ip_dns2: !secret ha_wifi_dns2
|
|
|
|
# MQTT Settings
|
|
mqtt_server: !secret ha_mqtt_server
|
|
mqtt_username: !secret ha_mqtt_username
|
|
mqtt_password: !secret ha_mqtt_password
|
|
mqtt_topic: "esphome" # main topic for the mqtt server, call it what you like
|
|
|
|
# Web Server Settings
|
|
web_server_username: !secret web_server_username
|
|
web_server_password: !secret web_server_password
|
|
|
|
# Switch Naming
|
|
switch_1_name: "Red"
|
|
switch_2_name: "White"
|
|
switch_3_name: "Green"
|
|
switch_4_name: "Orange"
|
|
switch_5_name: "Blue"
|
|
switch_5b_name: "Blue (Double)"
|
|
switch_5c_name: "Blue (Hold)"
|
|
# switch_6_name: "Spare"
|
|
variable_1_name: "Dimmer"
|
|
variable_1_full_scale: "3.14" # ADC reading when at 100% (adjust after calibration)
|
|
variable_1_min_scale: "0.14" # volts at ADC for 0% (adjust after calibration)
|
|
|
|
# Device Settings
|
|
log_level: "INFO" # Define logging level: NONE, ERROR, WARN, INFO, DEBUG (Default), VERBOSE, VERY_VERBOSE
|
|
update_interval: "60s" # update time for for general sensors etc
|
|
pwm_freq: "1000Hz" # ESPHome default is 1000Hz, but will go much higher... (not much point for a switch LED)
|
|
|
|
# Network reconnect every x hours to ensure best access point
|
|
# This is my own script. No need to use if only one AP or it is always fixed.
|
|
base_interval_hours: "23" # Base interval in hours
|
|
random_offset_max_minutes: "59" # Max random offset in minutes
|
|
|
|
# Enables faster network connections, with last connected SSID being connected to and
|
|
# no full scan for SSID being undertaken
|
|
wifi_fast_connect: "false"
|
|
|
|
# Define a domain for this device to use. i.e. iot.home.lan (so device will appear as
|
|
# athom-smart-plug-v2.iot.home.lan in DNS/DHCP logs)
|
|
dns_domain: ".local"
|
|
|
|
# Automatically add the mac address to the name eg so you can use a single firmware for all devices
|
|
# I don't tend to like doing this, but good for many identical devices
|
|
add_mac_suffix: "false"
|
|
|
|
# Enable or disable the use of IPv6 networking on the device
|
|
ipv6_enable: "false"
|
|
|
|
##########################################################################################
|
|
# PACKAGES
|
|
# Included Common Packages from other files.
|
|
# https://esphome.io/components/packages.html
|
|
##########################################################################################
|
|
# NOTE: ALL COMMENTED AS FOR THIS TEST EVERYTHING IS IN ONE YAML FILE (except no SNTP)
|
|
##########################################################################################
|
|
#packages:
|
|
#common_wifi: !include
|
|
# file: common/network_common.yaml
|
|
# vars:
|
|
# local_device_name: "${device_name}"
|
|
# local_static_ip_address: "${static_ip_address}"
|
|
# local_ota_pass: "${ota_pass}"
|
|
#common_api: !include
|
|
# file: common/api_common.yaml
|
|
# vars:
|
|
# local_api_key: "${api_key}"
|
|
#common_webportal: !include
|
|
# file: common/webportal_common.yaml
|
|
#common_mqtt: !include
|
|
# file: common/mqtt_common.yaml
|
|
# vars:
|
|
# local_device_name: "${device_name}"
|
|
#common_sntp: !include
|
|
# file: common/sntp_common.yaml
|
|
#common_general_sensors: !include
|
|
# file: common/sensors_common.yaml
|
|
# vars:
|
|
# local_friendly_name: "${friendly_name}"
|
|
# local_update_interval: "${update_interval}"
|
|
|
|
##########################################################################################
|
|
# WIFI COMPONENT
|
|
# https://esphome.io/components/wifi.html
|
|
#
|
|
# Power Save mode (can reduce wifi reliability)
|
|
# NONE (least power saving, Default for ESP8266)
|
|
# LIGHT (Default for ESP32)
|
|
# HIGH (most power saving)
|
|
##########################################################################################
|
|
wifi:
|
|
ssid: ${wifi_ssid}
|
|
password: ${wifi_password}
|
|
#enable_rrm: true # (ESP32 only) enable 802.11k Radio Resource Management
|
|
#enable_btm: true # (ESP32 only) enable 802.11v BSS Transition Management
|
|
#power_save_mode: LIGHT # https://esphome.io/components/wifi.html#wifi-power-save-mode
|
|
manual_ip: # optional static IP address
|
|
static_ip: ${static_ip_address}
|
|
gateway: ${static_ip_gateway}
|
|
subnet: ${static_ip_subnet}
|
|
dns1: ${static_ip_dns1}
|
|
dns2: ${static_ip_dns2}
|
|
ap: # Details for fallback hotspot in case wifi connection fails https://esphome.io/components/wifi.html#access-point-mode
|
|
ssid: ${device_name} AP
|
|
password: ${fallback_ap_password}
|
|
ap_timeout: 10min # Time until it brings up fallback AP. default is 1min
|
|
# Allow rapid re-connection to previously connect WiFi SSID, skipping scan of all SSID
|
|
fast_connect: ${wifi_fast_connect}
|
|
# Define dns domain / suffix to add to hostname
|
|
domain: ${dns_domain}
|
|
|
|
#captive_portal: # extra fallback mechanism for when connecting if the configured WiFi fails
|
|
|
|
##########################################################################################
|
|
# ESPHome OTA UPDATES
|
|
# https://esphome.io/components/ota/esphome.html
|
|
##########################################################################################
|
|
ota:
|
|
- platform: esphome
|
|
password: ${ota_pass}
|
|
version: 2
|
|
|
|
##########################################################################################
|
|
# SAFE MODE
|
|
# Safe mode will detect boot loops
|
|
# https://esphome.io/components/safe_mode
|
|
##########################################################################################
|
|
safe_mode:
|
|
|
|
##########################################################################################
|
|
# NETWORK COMPONENT
|
|
# global configuration for all types of networks
|
|
# https://esphome.io/components/network.html
|
|
##########################################################################################
|
|
network:
|
|
enable_ipv6: ${ipv6_enable}
|
|
|
|
##########################################################################################
|
|
# MQTT CLIENT COMPONENT
|
|
# https://esphome.io/components/mqtt.html?highlight=mqtt
|
|
# MUST also have api enabled if you enable MQTT!
|
|
##########################################################################################
|
|
mqtt:
|
|
broker: ${mqtt_server}
|
|
topic_prefix: ${mqtt_topic}/${device_name}
|
|
username: ${mqtt_username}
|
|
password: ${mqtt_password}
|
|
discovery: false # enable entity discovery (true is default)
|
|
discover_ip: false # enable device discovery (true is default)
|
|
id: mqtt_client
|
|
reboot_timeout: 0s # same for MQTT
|
|
|
|
##########################################################################################
|
|
# WEB SERVER COMPONENT
|
|
# https://esphome.io/components/web_server.html
|
|
# Web Portal for display and monitoring
|
|
# Turning this off is maybe a good idea to save resources, especially on an esp8266.
|
|
##########################################################################################
|
|
web_server:
|
|
port: 80
|
|
auth:
|
|
username: ${web_server_username} # probably a good idea to secure it
|
|
password: ${web_server_password}
|
|
|
|
##########################################################################################
|
|
# NATIVE API COMPONENT
|
|
# Enable the Home Assistant API
|
|
# https://esphome.io/components/api.html
|
|
##########################################################################################
|
|
api:
|
|
encryption:
|
|
key: ${api_key}
|
|
reboot_timeout: 0s # disables watchdog reboot on API failure
|
|
|
|
##########################################################################################
|
|
# ESPHome CORE CONFIGURATION
|
|
# https://esphome.io/components/esphome.html
|
|
##########################################################################################
|
|
esphome:
|
|
name: ${device_name}
|
|
friendly_name: ${friendly_name}
|
|
comment: ${description_comment} # Appears on the ESPHome page in HA
|
|
area: ${device_area}
|
|
on_boot:
|
|
then:
|
|
- lambda: |-
|
|
// if the user had manually left it ON, re-apply it now
|
|
if (id(vrelay4_manual_state)) {
|
|
id(vrelay_4).turn_on();
|
|
}
|
|
// now restore all your _other_ relays as you already had them
|
|
if (id(vrelay_1_state)) id(vrelay_1).turn_on();
|
|
if (id(vrelay_2_state)) id(vrelay_2).turn_on();
|
|
if (id(vrelay_3_state)) id(vrelay_3).turn_on();
|
|
if (id(vrelay_5_state)) id(vrelay_5).turn_on();
|
|
if (id(vrelay_5b_state)) id(vrelay_5b).turn_on();
|
|
if (id(vrelay_5c_state)) id(vrelay_5c).turn_on();
|
|
|
|
##########################################################################################
|
|
# ESP PLATFORM AND FRAMEWORK
|
|
# https://esphome.io/components/esp32.html
|
|
##########################################################################################
|
|
# Suggest using ESP-IDF Framework. Changes might need need to be cable flashed here to
|
|
# reset the partitioning
|
|
##########################################################################################
|
|
esp32:
|
|
board: esp32dev
|
|
framework:
|
|
type: esp-idf # "esp-idf" OR "arduino".
|
|
version: recommended # recommended, latest or dev
|
|
|
|
preferences:
|
|
flash_write_interval: 10s # not too important but anything written for reboot mem will wear the flash
|
|
|
|
##########################################################################################
|
|
# GLOBAL VARIABLES
|
|
# https://esphome.io/components/globals.html
|
|
##########################################################################################
|
|
# We are using globals here to store the states of the virtual relays
|
|
# They will also be restored on power loss.
|
|
##########################################################################################
|
|
globals:
|
|
- id: vrelay_1_state
|
|
type: bool
|
|
restore_value: yes
|
|
initial_value: 'false'
|
|
- id: vrelay_2_state
|
|
type: bool
|
|
restore_value: yes
|
|
initial_value: 'false'
|
|
- id: vrelay_3_state
|
|
type: bool
|
|
restore_value: yes
|
|
initial_value: 'false'
|
|
- id: vrelay_4_state
|
|
type: bool
|
|
restore_value: yes
|
|
initial_value: 'false'
|
|
- id: vrelay4_manual_state
|
|
type: bool
|
|
restore_value: yes
|
|
initial_value: 'false'
|
|
- id: vrelay4_timer_state
|
|
type: bool
|
|
restore_value: no
|
|
initial_value: 'false'
|
|
- id: vrelay_5_state
|
|
type: bool
|
|
restore_value: yes
|
|
initial_value: 'false'
|
|
- id: vrelay_5b_state
|
|
type: bool
|
|
restore_value: yes
|
|
initial_value: 'false'
|
|
- id: vrelay_5c_state
|
|
type: bool
|
|
restore_value: yes
|
|
initial_value: 'false'
|
|
|
|
- id: max_led_brightness
|
|
type: float
|
|
restore_value: yes
|
|
initial_value: '1.0' # default to 100% on first run
|
|
|
|
##########################################################################################
|
|
# LOGGER COMPONENT
|
|
# https://esphome.io/components/logger.html
|
|
# Logs all log messages through the serial port and through MQTT topics.
|
|
##########################################################################################
|
|
logger:
|
|
level: ${log_level} #INFO Level suggested, or DEBUG for testing
|
|
|
|
##########################################################################################
|
|
# STATUS LED
|
|
# https://esphome.io/components/status_led.html
|
|
##########################################################################################
|
|
# This is usually the blue LED on the ESP32 Dev board
|
|
# Status_LED can show ESPHome errors and warnings
|
|
##########################################################################################
|
|
status_led:
|
|
pin:
|
|
number: GPIO2
|
|
inverted: yes
|
|
|
|
##########################################################################################
|
|
# SCRIPT COMPONENT
|
|
# https://esphome.io/components/script.html
|
|
# Scripts can be executed nearly anywhere in your device configuration with a single call.
|
|
##########################################################################################
|
|
script:
|
|
# Restart Networking every x hours + rand mins. Starts on reboot and always runs
|
|
# This ensures that the device is connected to the best AP, but no need for it
|
|
# if one AP and it is always reliable.
|
|
- id: random_reconnect
|
|
mode: restart
|
|
then:
|
|
- lambda: |-
|
|
// Compute total delay: base hours + random offset minutes
|
|
uint32_t extra;
|
|
#if defined(ESP32)
|
|
// ESP32 (both Arduino & IDF builds) uses esp_random()
|
|
extra = esp_random() % (${random_offset_max_minutes} + 1);
|
|
#elif defined(ESP8266)
|
|
// ESP8266 Arduino core
|
|
extra = os_random() % (${random_offset_max_minutes} + 1);
|
|
#else
|
|
// Fallback to esp_random() on other platforms
|
|
extra = esp_random() % (${random_offset_max_minutes} + 1);
|
|
#endif
|
|
uint32_t total_s = ${base_interval_hours} * 3600 + extra * 60;
|
|
ESP_LOGI("random_reconnect", "Next reconnect in %u seconds", total_s);
|
|
// Delay inside lambda (blocks script execution but OK for reconnect timing)
|
|
delay(total_s * 1000);
|
|
- logger.log: "network_check: performing reconnect"
|
|
- wifi.disable: {}
|
|
- delay: 1s
|
|
- wifi.enable: {}
|
|
- script.execute: random_reconnect
|
|
# Button 4: Double-press short timer (should NOT restore after power loss)
|
|
- id: button4_short
|
|
then:
|
|
- lambda: |-
|
|
// Timed mode (not manual) → will NOT be restored on reboot
|
|
id(vrelay4_manual_state) = false;
|
|
- switch.turn_off: vrelay_4 # keep the virtual relay OFF during timer
|
|
- lambda: |-
|
|
// Start 30 s fast-flash timer
|
|
id(vrelay4_timer_state) = true;
|
|
{
|
|
auto call = id(led4).turn_on();
|
|
call.set_brightness(id(max_led_brightness));
|
|
call.set_effect("Flash Fast");
|
|
call.perform();
|
|
}
|
|
- delay: 30s
|
|
- lambda: |-
|
|
// Timer expired → clear
|
|
id(vrelay4_timer_state) = false;
|
|
- light.turn_off: led4
|
|
|
|
# Button 4: Hold long timer (should NOT restore after power loss)
|
|
- id: button4_long
|
|
then:
|
|
- lambda: |-
|
|
// Timed mode (not manual) → will NOT be restored on reboot
|
|
id(vrelay4_manual_state) = false;
|
|
- switch.turn_off: vrelay_4 # keep the virtual relay OFF during timer
|
|
- lambda: |-
|
|
// Start 60 min slow-flash timer
|
|
id(vrelay4_timer_state) = true;
|
|
{
|
|
auto call = id(led4).turn_on();
|
|
call.set_brightness(id(max_led_brightness));
|
|
call.set_effect("Flash Slow");
|
|
call.perform();
|
|
}
|
|
- delay: 60min
|
|
- lambda: |-
|
|
// Timer expired → clear
|
|
id(vrelay4_timer_state) = false;
|
|
- light.turn_off: led4
|
|
|
|
##########################################################################################
|
|
# BINARY SENSORS
|
|
# https://esphome.io/components/binary_sensor/
|
|
##########################################################################################
|
|
# These are the input buttons on GPIO.
|
|
# No "mode: INPUT_PULLUP" needed as they have external pullups
|
|
# Switches pull to GND so "inverted:true" for ESPHome to report ON when pressed.
|
|
# They will toggle the virtual relays when pressed (the vrelays will toggle the LEDs)
|
|
##########################################################################################
|
|
binary_sensor:
|
|
- platform: gpio
|
|
pin:
|
|
number: GPIO19
|
|
mode: INPUT
|
|
inverted: true
|
|
name: "Button 1: ${switch_1_name}"
|
|
filters:
|
|
- delayed_on: 50ms
|
|
- delayed_off: 50ms
|
|
on_press:
|
|
- switch.toggle: vrelay_1
|
|
|
|
- platform: gpio
|
|
pin:
|
|
number: GPIO35
|
|
mode: INPUT
|
|
inverted: true
|
|
name: "Button 2: ${switch_2_name}"
|
|
filters:
|
|
- delayed_on: 50ms
|
|
- delayed_off: 50ms
|
|
on_press:
|
|
- switch.toggle: vrelay_2
|
|
|
|
- platform: gpio
|
|
pin:
|
|
number: GPIO05
|
|
mode: INPUT
|
|
inverted: true
|
|
name: "Button 3: ${switch_3_name}"
|
|
filters:
|
|
- delayed_on: 50ms
|
|
- delayed_off: 50ms
|
|
on_press:
|
|
- switch.toggle: vrelay_3
|
|
|
|
- platform: gpio
|
|
pin:
|
|
number: GPIO33
|
|
mode: INPUT
|
|
inverted: true
|
|
name: "Button 4: ${switch_4_name}"
|
|
filters:
|
|
- delayed_on: 50ms
|
|
- delayed_off: 50ms
|
|
on_multi_click:
|
|
# Single click: cancel timers, then toggle relay+LED
|
|
- timing:
|
|
- ON for 50ms to 400ms
|
|
- OFF for at least 250ms
|
|
then:
|
|
- script.stop: button4_short
|
|
- script.stop: button4_long
|
|
- switch.toggle: vrelay_4
|
|
# Double click → short sequence
|
|
- timing:
|
|
- ON for 50ms to 400ms
|
|
- OFF for 50ms to 300ms
|
|
- ON for 50ms to 400ms
|
|
then:
|
|
- script.stop: button4_long
|
|
- script.execute: button4_short
|
|
# Hold → long sequence
|
|
- timing:
|
|
- ON for at least 2s
|
|
then:
|
|
- script.stop: button4_short
|
|
- script.execute: button4_long
|
|
|
|
- platform: gpio
|
|
pin:
|
|
number: GPIO16
|
|
mode: INPUT
|
|
inverted: true
|
|
name: "Button 5: ${switch_5_name}"
|
|
filters:
|
|
- delayed_on: 30ms
|
|
- delayed_off: 30ms
|
|
on_multi_click:
|
|
# Single click: if any of 5/5B/5C is on → turn them all off; else turn on 5
|
|
- timing:
|
|
- ON for 50ms to 400ms
|
|
- OFF for at least 250ms
|
|
then:
|
|
- lambda: |-
|
|
if (id(vrelay_5_state) || id(vrelay_5b_state) || id(vrelay_5c_state)) {
|
|
id(vrelay_5).turn_off();
|
|
id(vrelay_5b).turn_off();
|
|
id(vrelay_5c).turn_off();
|
|
} else {
|
|
id(vrelay_5).turn_on();
|
|
}
|
|
|
|
# Double click → vrelay_5b
|
|
- timing:
|
|
- ON for 50ms to 400ms
|
|
- OFF for 50ms to 300ms
|
|
- ON for 50ms to 400ms
|
|
then:
|
|
- switch.toggle: vrelay_5b
|
|
|
|
# Hold → vrelay_5c
|
|
- timing:
|
|
- ON for at least 2s
|
|
then:
|
|
- switch.toggle: vrelay_5c
|
|
|
|
# FUTURE: Board allows for 6 buttons
|
|
#- platform: gpio
|
|
# pin:
|
|
# number: GPIO12
|
|
# mode: INPUT
|
|
# inverted: true
|
|
# name: "Button 6: ${switch_6_name}"
|
|
# filters:
|
|
# - delayed_on: 50ms
|
|
# - delayed_off: 50ms
|
|
# on_press:
|
|
# - switch.toggle: vrelay_6
|
|
|
|
## DIAGNOSTIC ONLY SENSORS BELOW ##
|
|
- platform: status
|
|
name: "Network Status"
|
|
icon: mdi:check-network-outline
|
|
entity_category: "diagnostic"
|
|
|
|
##########################################################################################
|
|
# OUTPUT COMPONENT
|
|
# https://esphome.io/components/light/index.html
|
|
##########################################################################################
|
|
# An OUTPUT can be binary (0,1) or float, which is any value between 0 and 1.
|
|
# PWM Outputs such as "ledc" are float. https://esphome.io/components/output/ledc.html
|
|
# We could change frequency: "100Hz" and/or resolution: "12", but these are the default.
|
|
##########################################################################################
|
|
output:
|
|
- platform: ledc
|
|
id: led1_output
|
|
pin: GPIO21
|
|
frequency: ${pwm_freq}
|
|
- platform: ledc
|
|
id: led2_output
|
|
pin: GPIO25
|
|
frequency: ${pwm_freq}
|
|
- platform: ledc
|
|
id: led3_output
|
|
pin: GPIO18
|
|
frequency: ${pwm_freq}
|
|
- platform: ledc
|
|
id: led4_output
|
|
pin: GPIO26
|
|
frequency: ${pwm_freq}
|
|
- platform: ledc
|
|
id: led5_output
|
|
pin: GPIO17
|
|
frequency: ${pwm_freq}
|
|
|
|
# FUTURE: Board allows for 6 buttons
|
|
#- platform: ledc
|
|
# id: led6_output
|
|
# pin: GPIO13
|
|
# frequency: ${pwm_freq}
|
|
|
|
##########################################################################################
|
|
# LIGHT COMPONENT
|
|
# https://esphome.io/components/light/index.html
|
|
##########################################################################################
|
|
light:
|
|
# We are just going to use simple monochromatic component as only one colour to PWM control
|
|
# This doesn't actually do anything by itself, you need to tied it to an OUTPUT component.
|
|
- platform: monochromatic
|
|
id: led1
|
|
output: led1_output
|
|
name: "LED 1: ${switch_1_name}"
|
|
- platform: monochromatic
|
|
id: led2
|
|
output: led2_output
|
|
name: "LED 2: ${switch_2_name}"
|
|
- platform: monochromatic
|
|
id: led3
|
|
output: led3_output
|
|
name: "LED 3: ${switch_3_name}"
|
|
- platform: monochromatic
|
|
id: led4
|
|
output: led4_output
|
|
name: "LED 4: ${switch_4_name}"
|
|
effects:
|
|
- strobe:
|
|
name: "Flash Slow"
|
|
colors:
|
|
- state: ON
|
|
duration: 1s
|
|
- state: OFF
|
|
duration: 0.5s
|
|
- strobe:
|
|
name: "Flash Fast"
|
|
colors:
|
|
- state: ON
|
|
duration: 500ms
|
|
- state: OFF
|
|
duration: 100ms
|
|
- platform: monochromatic
|
|
id: led5
|
|
output: led5_output
|
|
name: "LED 5: ${switch_5_name}"
|
|
effects:
|
|
# Pulse 0.5s: smooth ramp between 0% and current brightness
|
|
- pulse:
|
|
name: "Pulse 0.5s"
|
|
transition_length:
|
|
on_length: 0.5s
|
|
off_length: 0.5s
|
|
update_interval: 1s
|
|
# Pulse 0.1s: ramp up 0.5s / down 0.1s
|
|
- pulse:
|
|
name: "Pulse 0.1s"
|
|
transition_length:
|
|
on_length: 0.5s
|
|
off_length: 0.1s
|
|
update_interval: 600ms
|
|
|
|
# FUTURE: Board allows for 6 buttons
|
|
#- platform: monochromatic
|
|
# id: led6
|
|
# output: led6_output
|
|
# name: "LED 6: ${switch_6_name}"
|
|
|
|
##########################################################################################
|
|
# SWITCH COMPONENT
|
|
# https://esphome.io/components/switch/
|
|
##########################################################################################
|
|
switch:
|
|
# Normally SWITCH would be for things like a relay output and turning that on and off.
|
|
# We are using it for virtual relays, that show up in Home Assistant etc, and toggling
|
|
# them along with the LEDs when the buttons are pressed.
|
|
# Separating them from the LEDs as outputs means we can do thinks like light blinking etc
|
|
# but still leave the switch outputs toggled on or off.
|
|
- platform: template
|
|
name: "Output 1: ${switch_1_name}"
|
|
id: vrelay_1
|
|
optimistic: true
|
|
restore_mode: RESTORE_DEFAULT_OFF
|
|
lambda: |-
|
|
return id(vrelay_1_state);
|
|
turn_on_action:
|
|
- lambda: |-
|
|
auto call = id(led1).turn_on();
|
|
call.set_brightness(id(max_led_brightness));
|
|
call.perform();
|
|
- lambda: |-
|
|
id(vrelay_1_state) = true;
|
|
turn_off_action:
|
|
- light.turn_off: led1
|
|
- lambda: |-
|
|
id(vrelay_1_state) = false;
|
|
|
|
- platform: template
|
|
name: "Output 2: ${switch_2_name}"
|
|
id: vrelay_2
|
|
optimistic: true
|
|
restore_mode: RESTORE_DEFAULT_OFF
|
|
lambda: |-
|
|
return id(vrelay_2_state);
|
|
turn_on_action:
|
|
- lambda: |-
|
|
auto call = id(led2).turn_on();
|
|
call.set_brightness(id(max_led_brightness));
|
|
call.perform();
|
|
- lambda: |-
|
|
id(vrelay_2_state) = true;
|
|
turn_off_action:
|
|
- light.turn_off: led2
|
|
- lambda: |-
|
|
id(vrelay_2_state) = false;
|
|
|
|
- platform: template
|
|
name: "Output 3: ${switch_3_name}"
|
|
id: vrelay_3
|
|
optimistic: true
|
|
restore_mode: RESTORE_DEFAULT_OFF
|
|
lambda: |-
|
|
return id(vrelay_3_state);
|
|
turn_on_action:
|
|
- lambda: |-
|
|
auto call = id(led3).turn_on();
|
|
call.set_brightness(id(max_led_brightness));
|
|
call.perform();
|
|
- lambda: |-
|
|
id(vrelay_3_state) = true;
|
|
turn_off_action:
|
|
- light.turn_off: led3
|
|
- lambda: |-
|
|
id(vrelay_3_state) = false;
|
|
|
|
- platform: template
|
|
name: "Output 4: ${switch_4_name}"
|
|
id: vrelay_4
|
|
optimistic: true
|
|
restore_mode: RESTORE_DEFAULT_OFF
|
|
lambda: |-
|
|
// our single "source of truth" is vrelay_4_state
|
|
return id(vrelay_4_state);
|
|
|
|
turn_on_action:
|
|
- lambda: |-
|
|
// a true manual toggle
|
|
id(vrelay4_manual_state) = true;
|
|
// clear any leftover timer (shouldn't happen)
|
|
id(vrelay4_timer_state) = false;
|
|
id(vrelay_4_state) = true;
|
|
{
|
|
auto call = id(led4).turn_on();
|
|
call.set_brightness(id(max_led_brightness));
|
|
call.perform();
|
|
}
|
|
|
|
turn_off_action:
|
|
- lambda: |-
|
|
// manual switch-off
|
|
id(vrelay4_manual_state) = false;
|
|
id(vrelay4_timer_state) = false;
|
|
id(vrelay_4_state) = false;
|
|
- light.turn_off: led4
|
|
|
|
- platform: template
|
|
name: "Output 5: ${switch_5_name}"
|
|
id: vrelay_5
|
|
optimistic: true
|
|
restore_mode: RESTORE_DEFAULT_OFF
|
|
lambda: |-
|
|
return id(vrelay_5_state);
|
|
turn_on_action:
|
|
- switch.turn_off: vrelay_5b
|
|
- switch.turn_off: vrelay_5c
|
|
- lambda: |-
|
|
auto call = id(led5).turn_on();
|
|
call.set_brightness(id(max_led_brightness));
|
|
call.perform();
|
|
- lambda: |-
|
|
id(vrelay_5_state) = true;
|
|
turn_off_action:
|
|
- light.turn_off: led5
|
|
- lambda: |-
|
|
id(vrelay_5_state) = false;
|
|
|
|
- platform: template
|
|
name: "Output 5B: ${switch_5b_name}"
|
|
id: vrelay_5b
|
|
optimistic: true
|
|
restore_mode: RESTORE_DEFAULT_OFF
|
|
lambda: |-
|
|
return id(vrelay_5b_state);
|
|
turn_on_action:
|
|
- switch.turn_off: vrelay_5
|
|
- switch.turn_off: vrelay_5c
|
|
- lambda: |-
|
|
auto call = id(led5).turn_on();
|
|
call.set_brightness(id(max_led_brightness));
|
|
call.set_effect("Pulse 0.5s");
|
|
call.perform();
|
|
- lambda: |-
|
|
id(vrelay_5b_state) = true;
|
|
turn_off_action:
|
|
- light.turn_off: led5
|
|
- lambda: |-
|
|
id(vrelay_5b_state) = false;
|
|
|
|
- platform: template
|
|
name: "Output 5C: ${switch_5c_name}"
|
|
id: vrelay_5c
|
|
optimistic: true
|
|
restore_mode: RESTORE_DEFAULT_OFF
|
|
lambda: |-
|
|
return id(vrelay_5c_state);
|
|
turn_on_action:
|
|
- switch.turn_off: vrelay_5
|
|
- switch.turn_off: vrelay_5b
|
|
- lambda: |-
|
|
auto call = id(led5).turn_on();
|
|
call.set_brightness(id(max_led_brightness));
|
|
call.set_effect("Pulse 0.1s");
|
|
call.perform();
|
|
- lambda: |-
|
|
id(vrelay_5c_state) = true;
|
|
turn_off_action:
|
|
- light.turn_off: led5
|
|
- lambda: |-
|
|
id(vrelay_5c_state) = false;
|
|
|
|
|
|
# FUTURE: Board allows for 6 buttons
|
|
#- platform: template
|
|
# name: "Output 6: ${switch_6_name}"
|
|
# id: vrelay_6
|
|
# lambda: |-
|
|
# return id(vrelay_6_state);
|
|
# turn_on_action:
|
|
# - light.turn_on: led6
|
|
# - lambda: |-
|
|
# id(vrelay_6_state) = true;
|
|
# turn_off_action:
|
|
# - light.turn_off: led6
|
|
# - lambda: |-
|
|
# id(vrelay_6_state) = false;
|
|
|
|
##########################################################################################
|
|
# SENSOR COMPONENT
|
|
# https://esphome.io/components/sensor/
|
|
##########################################################################################
|
|
sensor:
|
|
# Raw ADC reading from GPIO36
|
|
# ADC Component https://esphome.io/components/sensor/adc.html
|
|
- platform: adc
|
|
pin: GPIO36
|
|
id: dimmer_raw
|
|
name: "${variable_1_name} Raw"
|
|
attenuation: 11db
|
|
update_interval: 0.5s
|
|
on_value:
|
|
then:
|
|
- lambda: |-
|
|
// Convert raw ADC (x) to volts
|
|
float volts = x;
|
|
// Apply min/max calibration
|
|
float min_v = ${variable_1_min_scale};
|
|
float max_v = ${variable_1_full_scale};
|
|
// Calculate percentage between min and max
|
|
float pct = ((volts - min_v) / (max_v - min_v)) * 100.0;
|
|
// Clamp result between 0 and 100
|
|
if (pct > 100.0) pct = 100.0;
|
|
if (pct < 0.0) pct = 0.0;
|
|
// Publish to percentage sensor
|
|
id(dimmer_percent).publish_state(pct);
|
|
# Percentage sensor derived from raw ADC
|
|
- platform: template
|
|
id: dimmer_percent
|
|
name: "${variable_1_name}"
|
|
unit_of_measurement: "%"
|
|
accuracy_decimals: 0
|
|
# External supply voltage from GPIO39
|
|
- platform: adc
|
|
pin: GPIO39
|
|
name: "External Supply Voltage"
|
|
id: supply_voltage
|
|
attenuation: 12db
|
|
update_interval: 2s
|
|
filters:
|
|
- calibrate_linear: # https://esphome.io/components/sensor/#calibrate-linear
|
|
# Format: raw_value -> real_voltage_at_pin
|
|
- 1.80 -> 20.00 # Example: ADC reads X when pin is -> actually Y
|
|
- 1.35 -> 15.00
|
|
- 0.89 -> 10.00
|
|
#- multiply: 4.00 # Voltage divider ratio
|
|
unit_of_measurement: "V"
|
|
|
|
|
|
## DIAGNOSTIC ONLY SENSORS BELOW ##
|
|
- platform: uptime # Uptime for this device in seconds
|
|
name: "Uptime (s):"
|
|
update_interval: ${update_interval}
|
|
id: uptime_sensor
|
|
entity_category: "diagnostic"
|
|
- platform: wifi_signal # Wifi Strength
|
|
name: "Wifi (dB):"
|
|
id: wifi_signal_db
|
|
update_interval: ${update_interval}
|
|
entity_category: "diagnostic"
|
|
- platform: copy # Reports the WiFi signal strength in %
|
|
source_id: wifi_signal_db
|
|
name: "WiFi (%):"
|
|
filters:
|
|
- lambda: return min(max(2 * (x + 100.0), 0.0), 100.0);
|
|
unit_of_measurement: "%"
|
|
entity_category: "diagnostic"
|
|
|
|
##########################################################################################
|
|
# TEXT SENSOR COMPONENT
|
|
# https://esphome.io/components/text_sensor/index.html
|
|
##########################################################################################
|
|
text_sensor:
|
|
## DIAGNOSTIC ONLY SENSORS BELOW ##
|
|
- platform: version
|
|
name: "Version:"
|
|
entity_category: "diagnostic"
|
|
- platform: wifi_info
|
|
ip_address:
|
|
icon: mdi:ip-network
|
|
entity_category: diagnostic
|
|
name: "IP Address:"
|
|
ssid:
|
|
name: "Connected SSID"
|
|
icon: mdi:wifi-strength-2
|
|
entity_category: diagnostic
|
|
mac_address:
|
|
name: "MAC Address:"
|
|
icon: mdi:network-pos
|
|
entity_category: diagnostic
|
|
- platform: uptime # Uptime for this device human readable
|
|
name: "Uptime:"
|
|
icon: mdi:clock-start
|
|
update_interval: ${update_interval}
|
|
entity_category: "diagnostic"
|
|
|
|
##########################################################################################
|
|
# BUTTON COMPONENT
|
|
# https://esphome.io/components/button/
|
|
##########################################################################################
|
|
# Diagnostic buttons ued here and non-active by default, activated if needed in HA
|
|
##########################################################################################
|
|
button:
|
|
## DIAGNOSTIC ONLY BUTTONS BELOW ##
|
|
- platform: safe_mode
|
|
name: "Safe Mode Restart:"
|
|
entity_category: "diagnostic"
|
|
disabled_by_default: true # Need to activate them in HA
|
|
- platform: restart
|
|
name: "Restart:"
|
|
entity_category: "diagnostic"
|
|
disabled_by_default: true
|
|
- platform: factory_reset
|
|
name: "FACTORY RESET:"
|
|
entity_category: "diagnostic"
|
|
disabled_by_default: true
|
|
|
|
##########################################################################################
|
|
# NUMBER COMPONENT
|
|
# https://esphome.io/components/number/
|
|
##########################################################################################
|
|
number:
|
|
- platform: template
|
|
name: "LED Max Brightness"
|
|
id: led_max_brightness_number
|
|
optimistic: true
|
|
restore_value: true
|
|
initial_value: "1.0" # show 100% on first boot
|
|
min_value: 0.2
|
|
max_value: 1.0
|
|
step: 0.05
|
|
unit_of_measurement: "%"
|
|
set_action:
|
|
- lambda: |-
|
|
// store the new max
|
|
id(max_led_brightness) = x;
|
|
// if any LED is currently on, re-apply at new brightness
|
|
if (id(vrelay_1_state)) {
|
|
auto call = id(led1).turn_on();
|
|
call.set_brightness(x);
|
|
call.perform();
|
|
}
|
|
if (id(vrelay_2_state)) {
|
|
auto call = id(led2).turn_on();
|
|
call.set_brightness(x);
|
|
call.perform();
|
|
}
|
|
if (id(vrelay_3_state)) {
|
|
auto call = id(led3).turn_on();
|
|
call.set_brightness(x);
|
|
call.perform();
|
|
}
|
|
if (id(vrelay_4_state)) {
|
|
auto call = id(led4).turn_on();
|
|
call.set_brightness(x);
|
|
call.perform();
|
|
}
|
|
if (id(vrelay_5_state)) {
|
|
auto call = id(led5).turn_on();
|
|
call.set_brightness(x);
|
|
call.perform();
|
|
} |