root
195 lines
8.2 KiB
Plaintext
195 lines
8.2 KiB
Plaintext
##########################################################################################
|
|
##########################################################################################
|
|
# Moes Mains Dimmer
|
|
# Mains dimmer 150W single channel - Moes Wi-Fi Dimmer Module
|
|
# Module swapped to a ESP-02S module (from a Tuya WB2S)
|
|
#
|
|
# V1.0 2025-09-05 First Rev
|
|
##########################################################################################
|
|
#
|
|
# NOTES RE TUYA COMMS FOR THIS MODULE
|
|
# - Toggle DP1 (switch) to 1 or 0 for ON or OFF. The dimmer's MCU does the smooth ramp itself over a few seconds.
|
|
# - We set DP2 (brightness) on a 0-1000 scale; this is the actual brightness level your firmware uses.
|
|
# - We read DP2 back as a sensor (and also show a % view) so we can see the live target the MCU is using.
|
|
# - DP3 is exposed only as an optional minimum-brightness limit; not touched during normal dimming unless you tune the low end.
|
|
# - It appears that 11 is the lowest DP3 raw value. Brightness of 1% sets this, and 2% ramps it to 19.
|
|
# - 50% brightness is 501, so it is pretty linear (you can't set Gamma, see below - I guess you could script it though)
|
|
# - DP4 (mode) exists but left alone (unless you want to experiment with load type/behavior). I can't see it do anything. Disabled by default in HA.
|
|
# - gamma_correct supposedly remaps the HA slider (no Tuya traffic) BUT it must be set to 1 or weird behaviour (keeps ramping to 0)
|
|
# - setting logs to DEBUG will show what is happening with Tuya commands
|
|
#
|
|
##########################################################################################
|
|
##########################################################################################
|
|
|
|
##########################################################################################
|
|
# SPECIFIC DEVICE VARIABLE SUBSTITUTIONS
|
|
# If NOT using a secrets file, just replace these with the passwords etc (in quotes)
|
|
##########################################################################################
|
|
substitutions:
|
|
# Device Naming
|
|
device_name: "esp-loungemoesdimmer1"
|
|
friendly_name: "Lounge Lighting Moes Dimmer 1"
|
|
description_comment: "tba"
|
|
device_area: "Lounge" # Allows ESP device to be automatically linked to an 'Area' in Home Assistant.
|
|
|
|
# Project Naming
|
|
project_name: "Generic ESP8266.ESP-02S" # Project Details
|
|
project_version: "v1.0" # Project V denotes release of yaml file, allowing checking of deployed vs latest version
|
|
|
|
# Passwords & Secrets
|
|
api_key: !secret esp-api_key # unfortunately you can't use substitutions inside secrets names
|
|
ota_pass: !secret esp-ota_pass # unfortunately you can't use substitutions inside secrets names
|
|
static_ip_address: !secret esp-loungemoesdimmer1_ip
|
|
|
|
# Device Settings
|
|
#relay_icon: "mdi:lightbulb-group"
|
|
log_level: "INFO" # Define logging level: NONE, ERROR, WARN, INFO, DEBUG (Default), VERBOSE, VERY_VERBOSE
|
|
update_interval: "60s" # update time for for general sensors etc
|
|
|
|
#########################################################################################
|
|
# PACKAGES: Included Common Packages
|
|
# https://esphome.io/components/packages.html
|
|
##########################################################################################
|
|
# Comment some of these out where not needed, eg MQTT, Web portal, SNTP, General Sensors
|
|
##########################################################################################
|
|
packages:
|
|
common_wifi: !include
|
|
file: common/network_common.yaml
|
|
vars:
|
|
local_device_name: "${device_name}"
|
|
local_static_ip_address: "${static_ip_address}"
|
|
local_ota_pass: "${ota_pass}"
|
|
common_api: !include
|
|
file: common/api_common.yaml
|
|
vars:
|
|
local_api_key: "${api_key}"
|
|
#common_webportal: !include
|
|
# file: common/webportal_common.yaml
|
|
common_mqtt: !include
|
|
file: common/mqtt_common.yaml
|
|
vars:
|
|
local_device_name: "${device_name}"
|
|
common_sntp: !include
|
|
file: common/sntp_common.yaml
|
|
common_general_sensors: !include
|
|
file: common/sensors_common.yaml
|
|
vars:
|
|
local_friendly_name: "${friendly_name}"
|
|
local_update_interval: "${update_interval}"
|
|
|
|
#########################################################################################
|
|
# ESPHome
|
|
# https://esphome.io/components/esphome.html
|
|
#########################################################################################
|
|
esphome:
|
|
name: "${device_name}"
|
|
friendly_name: "${friendly_name}"
|
|
comment: "${description_comment}" # Appears on the esphome page in HA
|
|
area: "${device_area}"
|
|
project:
|
|
name: "${project_name}"
|
|
version: "${project_version}"
|
|
|
|
#########################################################################################
|
|
# ESP Platform and Framework
|
|
# https://esphome.io/components/esp32.html
|
|
#########################################################################################
|
|
esp8266:
|
|
board: esp01_1m
|
|
#early_pin_init: False # Initialise pins early to known values. Recommended false where switches are involved. Defaults to True.
|
|
board_flash_mode: dout # Default is dout
|
|
|
|
#########################################################################################
|
|
# ESPHome Logging Enable
|
|
# https://esphome.io/components/logger.html
|
|
#############################################
|
|
logger:
|
|
level: "${log_level}" #INFO Level suggested, or DEBUG for testing
|
|
baud_rate: 0 #set to 0 for no logging via UART, needed if you are using it for other serial things (eg PZEM)
|
|
#esp8266_store_log_strings_in_flash: false
|
|
#tx_buffer_size: 64
|
|
|
|
#########################################################################################
|
|
# STATUS LED
|
|
# https://esphome.io/components/status_led.html
|
|
#########################################################################################
|
|
status_led:
|
|
pin:
|
|
number: GPIO2
|
|
inverted: yes
|
|
|
|
#########################################################################################
|
|
# UART COMPONENT
|
|
# https://esphome.io/components/uart/
|
|
#########################################################################################
|
|
uart:
|
|
# Needed for the Tuya component.
|
|
# This UART talks to the coprocessing tuya chip
|
|
tx_pin: GPIO1
|
|
rx_pin: GPIO3
|
|
baud_rate: 9600
|
|
|
|
#########################################################################################
|
|
# TUYA MCU COMPONENT
|
|
# https://esphome.io/components/tuya/
|
|
#########################################################################################
|
|
tuya:
|
|
# logger baud_rate must be 0
|
|
id: tuyamcu
|
|
|
|
##########################################################################################
|
|
# LIGHT COMPONENT
|
|
# https://esphome.io/components/light/
|
|
##########################################################################################
|
|
light:
|
|
- platform: tuya
|
|
name: "Lounge Lighting Moes Dimmer 1"
|
|
switch_datapoint: 1 # ON/OFF
|
|
dimmer_datapoint: 2 # <-- CHANGED: brightness is DP2 on your unit
|
|
#min_value_datapoint: 3 # optional; comment this out if it misbehaves
|
|
min_value: 0
|
|
max_value: 1000
|
|
gamma_correct: 1.0
|
|
default_transition_length: 0s
|
|
|
|
##########################################################################################
|
|
# SENSOR COMPONENT
|
|
# https://esphome.io/components/sensor/
|
|
##########################################################################################
|
|
sensor:
|
|
# The raw value sent over the UART
|
|
# Listed as a dignostic, so will appear with the other diags in HA
|
|
- platform: tuya
|
|
id: dp2_brightness_raw
|
|
name: "Brightness (DP2 raw)"
|
|
sensor_datapoint: 2
|
|
entity_category: diagnostic
|
|
# Raw value as a percentage of max
|
|
- platform: template
|
|
name: "Brightness (%)"
|
|
unit_of_measurement: "%"
|
|
accuracy_decimals: 0
|
|
update_interval: 2s
|
|
lambda: |-
|
|
if (isnan(id(dp2_brightness_raw).state)) return NAN;
|
|
return (id(dp2_brightness_raw).state / 1000.0f) * 100.0f;
|
|
|
|
##########################################################################################
|
|
# SELECT COMPONENT
|
|
# https://esphome.io/components/select/
|
|
##########################################################################################
|
|
select:
|
|
# Experimental
|
|
- platform: tuya
|
|
id: dp4_mode
|
|
name: "DP4 Mode (experiment)"
|
|
enum_datapoint: 4
|
|
options:
|
|
0: "Mode 0"
|
|
1: "Mode 1"
|
|
2: "Mode 2"
|
|
3: "Mode 3"
|
|
4: "Mode 4"
|
|
255: "Default/Unknown"
|
|
entity_category: config
|
|
disabled_by_default: true |